Roland PNC-950 User Manual

Browse online or download User Manual for Print & Scan Roland PNC-950. Roland PNC-950 User`s manual

  • Download
  • Add to my manuals
  • Print

Summary of Contents

Page 1 - PNC-950PNC-950

ROLAND DG CORPOR ATIONPNC-950PNC-950PNC-950PNC-950PNC-950USER'S MANUAL

Page 2 - For Canada

4• Operation Panel* The TEST key and the cursor keys functiononly when the SETUP LED is lighted, andthe ROTATE key functions only when theSETUP LED is

Page 3 - Typographic Conventions

54 BASIC OPERATION4-1 Setting Up and Connection• Setting UpWhen arranging setup space for the PNC-950, make sure you have a space that is at least 905

Page 4 - To Ensure Safe Use

64-2 DIP Switch SettingsDIP switches settings must be made only when the power is turned off.The DIP switches are located on the right-hand side of th

Page 5 - Rating plate

72) Press the push-pin andremove the blade fromthe blade holder.Blade holderPush-pinBlade• Blade adjustment may be necessary in the following cases:-

Page 6 - To Ensure Correct Use

84-4 Loading the Sheet — SETUP Key• Turning on the PowerSwitch on the power switch on the left side of the PNC-950.When the power switch is pressed to

Page 7 - TABLE OF CONTENTS

9(1) Lower the sheet loading levers to raise the movable pinch rollers on the left and right, and move each of the pinch rollers all the wayto its res

Page 8 - 2 CHECKING SUPPLIED ITEMS

10If You Are Using a Flat Sheet- Ideally, the PNC-950 should be set up as shown in figure A or B below. If you are using a different setup configurat

Page 9 - 3 PART NAMES AND FUNCTIONS

11Movable pinch roller (left)SheetGuide lineSheetSheet loading leverPinch roll frameBack of thePNC-950Front of thePNC-950(5) After positioning the pin

Page 10 - • Operation Panel

12• About the Cutting AreaAbout 1 mm (about 0.04")24,998 mm(984-1/8")Cutting coordinateorigin (0,0)About 15 mm (about 9/16")Movable Pin

Page 11 - 4 BASIC OPERATION

134-6 Cutting Test to Check Blade Force — , , , , and TEST KeysBefore carrying out actual cutting, you may wish to perform a "cutting test&qu

Page 12 - 4-3 Installing the Blade

CAUTION1) Unauthorized copying or transferral, in whole or in part, of this manual is prohibited.2) The contents of this operation manual and the spec

Page 13 - Adjusting the Cutter Blade

144-7 Downloading Cutting DataThe unit will begin cutting when it receives cutting data sent from the computer.• Software SettingsWhen cutting with co

Page 14 - • Loading the Sheet

15• Continuing CuttingCutting After Changing the SheetFollow the procedure described from "Loading the Sheet" on page 8 to "4-7 Downloa

Page 15

164-9 When Cutting Is Completed(1) When cutting is finished, press down the sheet loading levers and remove the sheet. (See "Removing the Sheet&

Page 16 - If You Are Using a Flat Sheet

175 SETTINGS FOR EACH FUNCTION• Using a sheet effectively and cutting along the vertical dimension(Rotate function) -- ROTATE Key and ROTATE LEDThis f

Page 17 - • Removing the Sheet

18• Plotting on Paper Media — PEN MODE Key and PEN MODE LEDThe PNC-950 is also capable of plotting on paper media using plotter pens made by this comp

Page 18 - ORIGIN SET

196 ABOUT THE BLADEIf the blade becomes dullWhen the blade starts to lose its sharpness, try gradually increasing the blade force (refer to page 13, &

Page 19 - How to Adjust Blade Force

207 WHAT TO DO IF...If the PNC-950 doesn't run...PNC-950• Is the PNC-950 power on?Turn on the power.• Is the unit in SETUP status (the SETUP LED

Page 20 - 4-7 Downloading Cutting Data

21The POWER/ERROR LED is blinkingIf there is an error in the data downloaded to the PNC-950 from the computer, the PNC-950 generates an error (the POW

Page 21 - • Cutting a Thick Sheet

228 LIST OF CAMM-GL III INSTRUCTIONS*1: -(226-1) — +(226-1) *2: 0 — +(226-1) *3: -(226-1)° — +(226-1)° *4: 21(16) — 3A(16), 3C(16) — 7E(16)• mode1• m

Page 22 - Performing a Self-test

23• Instructions in mode1 and mode2Instruction Format Meaning of Parameter [Parameter Range (Default)] ExplanationIW IW LLx, LLy, URx, URy; LLx, LLy

Page 23 - 5 SETTINGS FOR EACH FUNCTION

iTypographic ConventionsThis manual uses certain typographic symbols, outlined below.This indicates a point requiring particular care to ensure safe u

Page 24 - PEN MODE

249 LIST OF DEVICE CONTROL INSTRUCTIONSDevice control instructions are used to determine the communication sequence between the PNC-950 and computerth

Page 25 - 6 ABOUT THE BLADE

25Instruction Format Parameter Range ([ ] is default) Explanation ESC .E [ESC].E None Outputs an error code related to RS-232C interface Output R

Page 26 - 7 WHAT TO DO IF

26Automatic backspace10 CHARACTER SETS

Page 27 - The sheet is not cut properly

2711 LIST OF OPTIONSOption name Product number DescriptionSpare blade (for ZEC-U1005 Cemented carbide blade (5 pcs/set)standard vinyl sheet)Spare bl

Page 28

2812 SPECIFICATIONS OF PNC-950, , , PNC-950Mechanism Media-movement methodMaximum cutting area Width: 584 mm (22-15/16")Length: 24,998 mm (984-

Page 29

29• Interface SpecificationsParallel Connector (in compliance withspecifications of Centronics) Serial Connector (RS-232C)1191836SignalnumberTerminaln

Page 30

C3070395BE V5-1

Page 31

ii To Ensure Safe UseIf you find some abnormality, immediately turn off the power switch and check the user's manual to find out what iswrong. WA

Page 32 - 10 CHARACTER SETS

iiiThese labels are affixed to the body of this product. The following figure describes the location and content of thesemessages. About the Labels A

Page 33

ivTo Ensure Correct UseThis product is a precision instru-ment and must be handled with care.When the unit is not in use for anextended period, detach

Page 34 - , ,

1Thanks and Best WishesThank you very much for purchasing the CAMM-1 PNC-950.Since we wish you many years of productive use of your PNC-950, we ask yo

Page 35 - • Interface Specifications

21 PRECAUTIONS IN USE• Ensure that the power supply voltage in within +/-10% of the machine's rated voltage.• Always be careful whenever the unit

Page 36 - C3070395BE V5-1

33 PART NAMES AND FUNCTIONSDIP SwitchesUsed to make various settings.Pen Force Control SliderSets the blade force to be used with the tool.Parallel (C

Comments to this Manuals

No comments