Roland KF-7 User Manual Page 9

  • Download
  • Add to my manuals
  • Print
  • Page
    / 28
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 8
9
3. Parameter Address Map (Model ID = 42H)
This map indicates address, size, Data (range), Parameter, Description, and Default Value of parameters which can be transferred using and “Data set 1 (DT1).”
All the numbers of address, size, Data, and Default Value are indicated in 7-bit Hexadecimal-form.
Address Block map
An outlined address map of the Exclusive Communication is as follows;
Address (H)
Block
40 00 00 +————————————————————————————————————+
| SYSTEM PARAMETERS |Individual
40 01 3F +————————————————————————————————————+
40 1x 00 +————————————————————————————————————+
| PART PARAMETERS |Individual
| (x = 0-F) |
40 2x 5A +————————————————————————————————————+
41 m0 00 +————————————————————————————————————+
| SRUM SETUP PARAMETERS |Individual
| (m = 0-1) |
41 m8 7F +————————————————————————————————————+
48 00 00 +————————————————————————————————————+
| SYSTEM PARAMETERS |Bulk
48 01 10 +————————————————————————————————————+
| PART PARAMETERS |Bulk
48 1D 0F +————————————————————————————————————+
49 m0 00 +————————————————————————————————————+
| DRUM SETUP PARAMETER |Bulk
| (m = 0-1) |
49 mE 17 +————————————————————————————————————+
There are two ways in which GS data is transmitted: Individual Parameter Transmission in which individual parameters are transmitted one by one, and Bulk Dump Transmission in which a
large amount of data is transmitted at once.
Individual Parameters
Individual Parameter Transmission transmits data (or requests data) for one parameter as one exclusive message (one packet of “F0 ..... F7”).
In Individual Parameter Transmission, you must use the Address and Size listed in the following “Parameter Address Map.” Addresses marked at “#” cannot be used as starting addresses.
System Parameters
Parameters related to the system of the device are called System Parameters.
Address (H)
Size (H) Data (H) Parameter Description Default Value (H) Description
40 00 00 00 00 04 0018-07E8 MASTER TUNE -100.0 - +100.0 [cent] 00 04 00 00 0 [cent]
40 00 01# Use nibblized data.
40 00 02#
40 00 03#
* Refer to section 4. Supplementary material, “About tuning” (p. 15).
40 00 04 00 00 01 00-7F MASTER VOLUME 0-127 7F 127
(= F0 7F 7F 04 01 00 vv F7)
40 00 05 00 00 01 28-58 MASTER KEY-SHIFT -24 - +24 [semitones] 40 0 [semitones]
40 00 06 00 00 01 01-7F MASTER PAN -63 (LEFT) - +63 (RIGHT) 40 0 (CENTER)
40 00 7F 00 00 01 00 MODE SET 00 = GS Reset,
127 = Exit GS mode (Rx. only)
* Refer to “System exclusive messages related to mode settings” (p.4).
40 01 10 00 00 10 00-40 VOICE RESERVE Part 10 (Drum Part) 02 2
40 01 11# Part 1 06 6
40 01 12# Part 2 02 2
40 01 13# Part 3 02 2
40 01 14# Part 4 02 2
40 01 15# Part 5 02 2
40 01 16# Part 6 02 2
40 01 17# Part 7 02 2
40 01 18# Part 8 02 2
40 01 19# Part 9 02 2
40 01 1A# Part 11 00 0
40 01 :# :
40 01 1F# Part 16 00 0
* The sum total of voices in the voice reserve function must be equal to or less than the number of the maximum polyphony. The maximum polyphony of this instrument is 128. For
compatibility with other GS models, it is recommended that the maximum polyphony be equal or less than 24.
40 01 30 00 00 01 00-07 REVERB MACRO 00: Room 1 04 Hall 2
01: Room 2
02: Room 3
03: Hall 1
04: Hall 2
05: Plate
06: Delay
07: Panning Delay
40 01 31 00 00 01 00-07 REVERB CHARACTER 0-7 04 4
40 01 32 00 00 01 00-07 REVERB PRE-LPF 0-7 00 0
40 01 33 00 00 01 00-7F REVERB LEVEL 0-127 40 64
40 01 34 00 00 01 00-7F REVERB TIME 0-127 40 64
40 01 35 00 00 01 00-7F REVERB DELAY FEEDBACK 0-127 000
* REVERB MACRO is a macro parameter that allows global setting of reverb parameters. When you select the reverb type with REVERB MACRO, each reverb parameter will be set to the most
suitable value.
* REVERB CHARACTER is a parameter that changes the reverb algorithm. The value of REVERB CHARACTER corresponds to the REVERB MACRO of the same number.
Page view 8
1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 27 28

Comments to this Manuals

No comments