Roland R-1000 Service Manual Page 93
- Page / 136
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Manual
Double Sheet Detector R1000 series E20
B0046991 / Rev. 1.6
Communication with the PLC
ROLAND ELECTRONIC GmbH · Otto-Maurer-Str. 17 · DE 75210 Keltern · Phone +49 (0)7236-9392-0 · Fax +49 (0)7236-9392-33
93
6.3.7 Typical measurement cycle for unit in destacking application
In order to warrant reliable functioning of the system the following operating cycle is recommended.
It is recommended to perform step 2 at each cycle.
1. Selection of the desired measuring program.
2. System test (This test should be performed).
See timing diagram chapter “6.3.1 System test“
3. The sensor is lowered onto the stack (this stack contains 1 or more sheets).
4. Measurement in order to detect last sheet in the stack (1-sheet signal = only one sheet in the
stack) provided there is no other metal under the stack.
5. Destack a sheet and move into monitoring position - at least 2 cm (.8 inch) away from stack.
6. Monitor and initiate action depending on measurement result:
• 0-sheet: Repeat destacking operation.
• 2-sheet: Initiate actions to remove double sheet or several sheets from destacker.
After the measure again.
Attention: During the removal operation measurement should be switched off because of
potentially undefined conditions, air gaps between sensor and sheet etc.
• 1-sheet: continue with point 7.
7. Transport sheet into the proper loading position.
8. Measurement to verify that the sensor is still on the sheet.
9. Release the sheet.
10. After de-stacking a sheet perform security check - Is the sheet de-stacked ?
11. Before de-stacking a new sheet perform point 1 “Selection of the desired measuring program“
or point 2 “System test“.
Pos: 49 /Doppel blech/Geräte/E2 0/6 Kommuni kation mit der S PS/Interne Ans teuerung @ 1\ mod_119546 3026484_501.d oc @ 5199 @ 2 @ 1
6.4 Internal control (Demo mode)
In this operating mode the system continuously executes measurements and activates
OUT0 … OUT3.
In general, this operating mode is suitable for demonstration purposes only.
Prerequisite: • Supply voltage applied
• System parameter 4 set to demo mode
• Teach-In has been executed
The external sensor switching via the A/B outputs does not function in this mode.
The refresh rate of the measurement is dependent on the sensor type:
• P30, P42, P42A, P75V 1 Second
• P36 2 Seconds
• P75 4 Seconds
- Double Sheet Detector E20 1
- R1000 series 1
- Copyright 2
- Table of contents 3
- 1 Safety advices 9
- 1.3 Intended use 10
- 2 Technical data 11
- Technical data 12
- E20-x-x-FP 13
- E20-4P-x-x-FP 13
- 2.3 Sensors 14
- 2.3.1 Sensor P30GS 14
- 2.3.2 Sensor P42AGS 15
- 2.3.3 Sensor P75VGS 16
- 2.5 Sensor cables 22
- Kabelabschirmung 23
- Cable shield 23
- Fig. 9: Sensor cable CPM12S 24
- Fig. 10: Sensor cable CPS 25
- 3 System description 29
- System description 30
- 3.3 Control unit 31
- 3.4.1 System parameters 32
- 3.4.2 Program parameters 34
- 3.5 Application samples 36
- Program Thickness Sensor 38
- 1 0.9 mm - * 38
- 1 1.5 mm 1, 2, 3, 4 39
- 1 1.0 mm 1, 2 40
- 2 1.8 mm 3, 4 40
- 4 Mounting 41
- Befestigungsbohrungen 43
- Mounting holes 43
- 4 x Ø 4,2 for 44
- Philips head screw 44
- M4 DIN 74 44
- Freiraum für Kabel 45
- Mounting space 45
- 4.3 Mounting of sensors 46
- Mounting 48
- “Spring travel” 53
- Clamping bracket SHK 54
- Spring loaded sensor bracket 54
- Fig. 24: Sensor holder SHX42 56
- 4.3.6 Clamping bracket SHK 59
- 5 Electrical installation 63
- Electrical installation 64
- PLC R1000 65
- 5.5 Cable connections 74
- 5.5.1 PLC cable 74
- 5.5.2 Voltage supply cable 74
- 6.1 PLC inputs 79
- 6.2 PLC output signals 79
- 6.2.2 Signal „Enable“ 80
- 6.3 Timing diagrams 80
- 6.3.1 System test 81
- Communication with the PLC 82
- 7 Start-up 99
- 7.2 Operation 100
- 7.3 Configuration menu 101
- 7.3.1 Main menu structure 101
- Start-up 102
- B0046991 / Rev. 1.6 102
- program param 104
- configuration 104
- 7.6 Program parameters 105
- TI val.: 0.97mm 108
- 7.7 System parameters 109
- Fig.. 65: Sensor selection 112
- Blank page 114
- 8 Operation 115
- Operation 116
- 8.3 Zero adjust 117
- 8.4 Teach-in 117
- Error code: 60 119
- 9.9 Other faults 122
- 10 Maintenance 123
- Maintenance 124
- 10.3 Replacement of fuses 125
- 10.6 Spare parts 126
- 11 Technical records 127
- 12 Order data 129
- 12.3 Cables 131
- 12.6 Other accessories 132
- 13 Appendix 133
- Standard working range 134
- End of Document 136
Related products and manuals for Measuring, testing & control Roland R-1000
(39 pages)3b-scientific Teltron Electron Diffraction Tube S manuals
Owner’s manuals and user’s guides for Health and hygiene 3b-scientific Teltron Electron Diffraction Tube S.
We providing 3 pdf manuals 3b-scientific Teltron Electron Diffraction Tube S for download free by document types: User Manual
Comments to this Manuals