Roland PNC-950 User Manual

USER'S MANUAL* This User's Manual is intended for the PNC-1860, PNC-1410, as well as PNC-1210.PNC-1860PNC-1860PNC-1860PNC-1860PNC-1860PNC-14

21 cut 50Cm/s0.250mm 30gfDisplayProvides menu display, configurationpreferences, coordinates, as well aserror messages for troubleshooting.2-

33 BASIC OPERATION* In this manual, sections that explaincommons points for the PNC-1860/1410/1210 use only illustrations of thePNC-1860. Some detail

43-2 Installing the CutterDo not touch the tip of the blade with your fingers, as the cutting performance of the blade will be impaired.Always make s

53-3 Loading the MaterialBelow are shown the allowable widths (horizontal dimension) of materials that can be loaded and the maximum widths that can

6StopperIf the diameter of the rolled sheet core is 72 mm (2-7/8") or lessInstall the shaft here if the amount of sheet remaining is small.Shafts

7(3) Pull out as much from the roll as needed, and pass the materialfrom the back of the main unit to the front as shown in thefigure.At this time, l

8Pass the Material Loading Flat Material (Standard-size Material, Cut Material, Etc.)(1) Pass the material between the pinch rollers and the gritrolle

9(2) Move the left and right pinch rollers so that they are close to therespective left and right edges of the material. When using a materialthat is

10 To Perform Long CuttingAREA LENGTHMOVE < 1.0m> AREA LENGTHMOVE < 2.0m> 1 CUT 50cm/s0.250mm 30gf WIDTH LENGTH 14612

11Press MENU.(8)PROTOCOL 1STOP DATA PARITYPROTOCOL 2BAUD HANDSHAKEAREA AXISREPLOT SUBMENUVS-COMND FS-CMNDCOMAAND I/OUse or to select.Press EN

NOTICEGrounding InstructionsDo not modify the plug provided - if it will not fit the outlet,have the proper outlet installed by a qualified electrici

123-5 Cutting Test - Setting Cutting Speed, Blade Force, and Blade CompensationFor optimum performance, it is necessary to set cutting conditions tha

13Cutting speedBlade forceBlade compensationToo fastToo slowToo largeToo smallToo largeToo smallCutting takes more time. Some parts of the sheet remai

14 Continuing CuttingCutting after changing the materialAgain carry out the procedure described from “3-3 Loading the Material” to “3-6 Downloading C

153-7 Applying the Completed Cutout(1) Open the front cover.For roll materialUse the cutter tool to cut off the completed portionfrom the roll.For a

16Cleaning the bodyUse water or alcohol to clean, and wipe gently with a clean cloth. Wipe the operation panel and display gently with a clean, softcl

175 ABOUT THE CUTTING AREA6 USING THE DISPLAY MENUSThis section describes the basic steps for using the display menus. Use this information together

18 WIDTH LENGTH 14612 ------REPLOTSTART CLEARAXIS ROTATION<0deg> 90degAREA LENGTHMOVE < 1.0m>1 CUT 50cm/s0.250mm 30gfARE

19HANDSHAKE<H-WIRE>XON/OFFBAUD RATE 19200 <9600>PARITY MODE<NONE>ODD EVENDATA BIT 7 <8>STOP BIT<1> 2PROTOCOL 2 BAUD HAN

20MENU Explanation DefaultPage where explainedDetermining the type of sheet loadedSELECT SHEETThis selects the type of sheet to be used ("Roll,&q

21MENUExplanationDefaultPage where explained Feed the loaded sheetAREAThis moves the sheet by the length to be cut before actual cutting is performed,

Typographic Conventions ...

22[90° Rotation]YXYX[0° Rotation] 2 ROTATEWhenever you employ the Rotate function (which allows you to rotate a character 90 degrees), the origin will

23 3 CROPMARKThis is used when cutting around pre-printed graphics on a material, such as when making stickers or seals. With the PNC-1860/1410/1210,

249 BLADES AND MATERIALS* The values for lifespan are intended to serve as a general guide when cutting materials of identical type.MaterialCarrier pa

25Before cutting, plotting using pen and paper can ensure that your design is correct without wasting materials.This feature can also be used to plot

2611 WHAT TO DO IF...11-1 What to do if...PNC-1860/1410/1210 troubleshootingIs the power cord connected correctly?Connect the power cord included w

27A message appears on the displayThe location of one or more of the pinch rollers is not correct.If this happens, raise the sheet loading levers and

28The sheet slips away from the pinch rollers during the cutting processMake sure the sheet is parallel with the grit roller.If the front edge of the

2912 SUPPORTED INSTRUCTION SETSA "CAMM-GL III Programmer's Manual" is available for separate purchase for those wishing to create their

30Automatic backspace13 CHARACTER SET

31PNC-1860 PNC-1410 PNC-1210Mechanism Media-movement methodDriving method Digital control servo motorMaximum cutting area1195 mm (W) x 24998 mm (L) (4

iTypographic ConventionsThis manual uses certain typographic symbols, outlined below. This indicates a point requiring particular care to ensure safe

32Signal NumberTerminal NumberSignal NumberPin ConnectionNC 36 18 HIGH**HIGH* 35 17 GNDNC 34 16 GNDGND 33 15 NCHIGH* 32 14 NCNC 31 13 HIGH*GND30 12 GN

R9-980506

ii To Ensure Safe UseNever disassemble or modifythis product.Do not allow liquids, metalobjects or flammables inside themachine.Fire orbreakdownmay re

Rating labeliiiDo not allow the hands within thespace to the front or rear of the unitwhile in operation. About the Labels Affixed to the UnitThese la

To Ensure Correct UseThis product is a precision instrumentand must be handled with care.Do not install in an area subject to dust,high humidity or po

vMEMO

1Check the following to make sure that you received all the items that were shipped along with the unit.Blade HolderXD-CH2 : 1Power Cord: 1Blade(Cemen