Roland FR-3sb User Manual download pdf (Page 49)

Treble Octave Tx

V-Accordion

Treble Octave Tx

(–3~0~3, Default setting: 0) This param-

eter allows you to transpose the Note-

on messages transmitted by the Treble

section up to three octaves up or down.

This can be used for songs where an accordion register

of the Treble section (for example) should be doubled by

a piccolo flute played by an external module whose

notes would be far too low if they were used as is. As

stated above, each MIDI note has a unique number. This

parameter allows you to add (or subtract) 12 (“1”

octave), 24 (“2” octaves) or 36 (“3” octaves) to (from)

the note numbers generated by your playing.

Note: “TX” means that this parameter only applies to the note

messages transmitted to external devices. Messages the FR-3

receives from another device are not affected by it.

Bass/Free Bass TX/RX Channel

(Off, 1~16, Default setting: 2) This

parameter allows you to define the MIDI

channel for the bass buttons or Free

Bass (accordion) section, depending on which mode is

currently active. The assignment set here applies both

to the transmission (“TX”) and reception (“RX”) of MIDI

data. Obviously, “TX” is only used when “MId” (see

above) is set to “Out”, while the “RX” part is only used

when “MId” is set to “In”. Select “Off” if the Bass or Free

Bass section should neither receive nor transmit MIDI

data.

Note: Though it is perfectly possible to assign the same MIDI

channel to several sections, the result is usually disappointing

and may lead to a lot of confusion.

Bass/Free Bass Octave TX

(–3~0~3, Default setting: 0) This param-

eter allows you to transpose the Note-

on messages transmitted by the bass

buttons or Free Bass section up to three octaves up or

down.

Chord TX/RX Channel

(Off, 1~16, Default setting: 3) This

parameter allows you to define the MIDI

channel for the chord buttons when

they are used to play the selected accordion register.

The assignment set here applies both to the transmis-

sion (“TX”) and reception (“RX”) of MIDI data. Obviously,

“TX” is only used when “MId” (see above) is set to “Out”,

while the “RX” part is only used when “MId” is set to

“In”.

Note: Though it is perfectly possible to assign the same MIDI

channel to several sections, the result is usually disappointing

and may lead to a lot of confusion.

Chord Octave TX

(–3~0~3, Default setting: 0) This param-

eter allows you to transpose the Note-

on messages transmitted by the chord

buttons up to three octaves up or down.

Orchestra TX/RX Channel

(Off, 1~16, Default setting: 3) This

parameter allows you to define the MIDI

channel for the Treble Orchestra part.

The assignment set here applies both to the transmis-

sion (“TX”) and reception (“RX”) of MIDI data. Obviously,

“TX” is only used when “MId” (see above) is set to “Out”,

while the “RX” part is only used when “MId” is set to

“In”.

Orchestra Octave TX

(–3~0~3, Default setting: 0) This param-

eter allows you to transpose the Note-

on messages transmitted by the Orches-

tra section.

Note: “TX” means that this parameter only applies to the note

messages transmitted to external devices. Messages the FR-3

receives from another device are not affected by it.

Orchestra Bass TX/RX Channel

(Off, 1~16, Default setting: 5) This

parameter allows you to define the MIDI

channel for the ORCH BASS part. The

assignment set here applies both to the transmission

(“TX”) and reception (“RX”) of MIDI data. Obviously, “TX”

is only used when “MId” (see above) is set to “Out”,

while the “RX” part is only used when “MId” is set to

“In”.

Orchestra Bass Octave TX

(–3~0~3, Default setting: 0) This param-

eter allows you to transpose the Note-

on messages transmitted by the ORCH

BASS part.

Orchestra Chord TX/RX Channel

(Off, 1~16, Default setting: 6) This

parameter allows you to define the MIDI

channel for the ORCH CHORD part. The

assignment set here applies both to the transmission

(“TX”) and reception (“RX”) of MIDI data. Obviously, “TX”

is only used when “MId” (see above) is set to “Out”,

while the “RX” part is only used when “MId” is set to

“In”.

Orchestra Chord Octave TX

(–3~0~3, Default setting: 0) This param-

eter allows you to transpose the Note-

on messages transmitted by the ORCH

CHORD part.

Orchestra Free Bass TX/RX Channel

(Off, 1~16, Default setting: 7) This

parameter allows you to define the MIDI

channel for the ORCH FREE BS part. The

assignment set here applies both to the transmission

(“TX”) and reception (“RX”) of MIDI data. Obviously, “TX”

is only used when “MId” (see above) is set to “Out”,

while the “RX” part is only used when “MId” is set to

“In”.

trO

bFr

bfO

CHd

CHO

OrC

OrO

Obs

ObO

OCH

OCO

Ofb

1 2 ... 44 45 46 47 48 49 50 51 52 53 54 ... 65 66

Comments to this Manuals

No comments

Roland FR-3sb User Manual Page 49

Comments to this Manuals

Related products and manuals for The input devices Roland FR-3sb