Roland JUNO-Di User Manual download pdf (Page 64)

Detailed Settings for Performance Functions

Use the dial to set the desired value.

* The target affected by the function assigned by “Type” will depend on the settings of JUNO-Di.

If you’re playing a single sound, the effect will apply to the currently selected sound.

If you’re playing multiple sounds (i.e., when the [PERFORM] button is lit), the effect will apply as follows.

• In Dual or Super Layer mode: all parts

• In Split, or otherwise: the currently selected part

Press the [EXIT] button to leave the edit screen.

SOLO SYNTH

Item Value Description

Level

0–127 Sets the volume of the Solo Synth.

Range

2OCT, 4OCT, 8OCT

Sets the Solo Synth to a pitch range of 2 octaves, 4 octaves, or 8 octaves.

EXPRESSION

Item Value Description

Range Min

0–127

Lower limit of the range of the Expression.

The effect will be applied when the position of your hand above the D Beam

controller is lower than this value.

Range Max

0–127

Upper limit of the range of the Expression.

The effect will be applied when the position of your hand above the D Beam

controller is above this value.

* By setting “Range Max” below “Range Min” you can invert the range of change.

ASSIGNABLE

Item Value Description

Type

MODULATION,

PORTA-TIME,

VOLUME,

PAN,

PORTAMENTO,

SOSTENUTO,

RESONANCE,

RELEASE-TIME,

ATTACK-TIME,

CUTOFF,

DECAY-TIME,

VIB-RATE,

VIB-DEPTH,

VIB-DELAY,

CHORUS-SEND,

REVERB-SEND,

AFTERTOUCH,

BEND-UP,

BEND-DOWN,

START/STOP

The D Beam controller can control the following functions.

The number in parentheses ( ) is the controller number of the control change message produced by the D Beam controller

when the corresponding function is assigned.

* The target of the following functions will depend on the current settings. For details, refer to the note that follows the table.

MODULATION (CC01):

Vibrato

PORTA-TIME (CC05):

Portamento time (p. 59)

VOLUME (CC07):

Level

PAN (CC10):

Pan (left/right position of the tone)

PORTAMENTO (CC65):

Portamento switch (p. 59)

SOSTENUTO (CC66):

The sound will be sustained only for keys that were already pressed.

RESONANCE (CC71):

Resonance (p. 66)

RELEASE-TIME (CC72):

Release time (p. 65)

ATTACK-TIME (CC73):

Attack time (p. 65)

CUTOFF (CC74):

Cutoff (p. 66)

DECAY-TIME (CC75):

Decay time (p. 65)

VIB-RATE (CC76):

Vibrato speed

VIB-DEPTH (CC77):

Vibrato depth

VIB-DELAY (CC78):

Vibrato delay time

CHORUS-SEND (CC93):

The amount of the chorus

REVERB-SEND (CC91):

The amount of the reverb

AFTERTOUCH:

Channel aftertouch

BEND-UP:

The pitch will rise when you bring your hand closer to the D Beam controller. The amount of available pitch

change is determined by the value set for “Bend Range Up” (p. 59).

BEND-DOWN:

The pitch will fall when you bring your hand closer to the D Beam controller.The amount of available pitch

change is determined by the value set for “Bend Range Down” (p. 59).

START/STOP:

By moving your hand over the D Beam you can start/stop the Song Player (p. 72) or Rhythm Pattern (p. 74).

Range Min

0–127

Lower limit of the range of the D Beam controller.

The effect will be applied when the position of your hand above the D Beam controller is lower than this value.

Range Max

0–127

Upper limit of the range of the D Beam controller.

The effect will be applied when the position of your hand above the D Beam controller is above this value.

* By setting “Range Max” below “Range Min” you can invert the range of change.

Range Min

Range Max

JUNO-Di_e.book 64 ページ２００９年６月２２日　月曜日　午前９時２３分

1 2 ... 59 60 61 62 63 64 65 66 67 68 69 ... 135 136

Comments to this Manuals

No comments

Roland JUNO-Di User Manual Page 64

Comments to this Manuals

Related products and manuals for Musical Instruments Roland JUNO-Di