Roland VS-300 User Manual download pdf (Page 101)

6. About the Menus

[MEDIA CLAMP]

Setting range: LONG, SHORT, NONE

Default value: SHORT

This makes the setting for the type of media clamps used.

[LONG]: Select this value when you're using the long media

clamps. Note that the long media clamps interfere with the sepa-

rating knife, so when [LONG] is selected, media-separation op-

erations are not performed.

[SHORT]: Select this value when you're using the short media

clamps.

[NONE]: Select this value when you're not using any media clamps.

[INK REMAINING]

This shows the amount of ink left after each of the ink cartridges

has been installed. The fewer the markers, the less ink is left.

If a partially used ink cartridge is removed and reinstalled, or if a

partially used ink cartridge is installed, the cartridge is taken to be

unused, and the displayed amount of remaining ink is not true.

[HEAD CLEANING] > [MEDIUM]

This performs cleaning of the printing heads. This performs clean-

ing that is more powerful than the cleaning carried out by press-

ing the [CLEANING] key. If no improvement is obtained by per-

forming cleaning several times using the [CLEANING] key, then

execute this menu item.

This cleaning causes more head wear and uses up more ink than

cleaning using the [CLEANING] key, so you should execute it

only as seldom as necessary.

[HEAD CLEANING] > [POWERFUL]

This performs cleaning of the printing heads. This performs clean-

ing that is more powerful than the cleaning carried out by using

[MEDIUM]. If no improvement is obtained by performing clean-

ing several times using [MEDIUM], then execute this menu item.

This cleaning causes more head wear and uses up more ink than

cleaning using [MEDIUM], so you should execute it only as sel-

dom as necessary.

6-2 Detailed Descriptions of the Menus

Cutting Configuration Menu

[FORCE]

Setting range: 30 to 300gf (in steps of 5gf)

Default value: 50gf

This sets the blade force used during cutting.

When [CUTTING PRIOR] on the main menu has been set to

[COMMAND], the program's settings for the cutting conditions

take priority. To give priority to the cutting conditions set on the

machine, turn off the program settings, or set the [CUTTING

PRIOR] menu item to [MENU].

[SPEED]

Setting range: 1 to 30cm/s (in steps of 1cm/s)

Default value: 30cm/s

This sets the cutting speed used during cutting.

When [CUTTING PRIOR] on the main menu has been set to

[COMMAND], the program's settings for the cutting conditions

take priority. To give priority to the cutting conditions set on the

machine, turn off the program settings, or set the [CUTTING

PRIOR] menu item to [MENU].

[OFFSET]

Setting range: 0.000 to 1.500mm (in steps of 0.025mm)

Default value: 0.250mm

This sets the blade offset used during cutting.

When [CUTTING PRIOR] on the main menu has been set to

[COMMAND], the program's settings for the cutting conditions

take priority. To give priority to the cutting conditions set on the

machine, turn off the program settings, or set the [CUTTING

PRIOR] menu item to [MENU].

[UP-SPEED]

Setting range: 1 to 30cm/s (in steps of 1cm/s)

Default value: 30cm/s

This sets the up speed for the blade (the speed when the blade is

raised).

When [CUTTING PRIOR] on the main menu has been set to

[COMMAND], the program's settings for the cutting conditions

take priority. To give priority to the cutting conditions set on the

machine, turn off the program settings, or set the [CUTTING

PRIOR] menu item to [MENU].

1 2 ... 96 97 98 99 100 101 102 103 104 105 106 ... 114 115

Comments to this Manuals

No comments

Roland VS-300 User Manual Page 101

Comments to this Manuals

Related products and manuals for Print & Scan Roland VS-300