Roland VS-300 User Manual Page 77
- Page / 115
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
75
5. Maintenance
Replacing an Ink Cartridge
1
Remove the ink cartridge from the ink-cartridge
port.
2
Gently shake the new ink cartridge, then insert it slowly.
If Ink Runs Out During Printing
If ink runs out during printing, a warning beep sounds and the screen shown in the figure appears.
Replace the ink cartridge. Ignoring the message and continuing printing without replacing the ink may adversely affect
image quality, resulting in faintness or other problems.
Replacing Ink (When Set to the [STOP] Mode)
1
Pull out the ink cartridge indicated by the flashing number on the display.
2
Gently shake the new ink cartridge, then insert it slowly.
Ink-cartridge port
5-1 Replacing the Ink Cartridges
1 2 3 4
The behavior that occurs when it becomes necessary to replace ink while printing is in progress differs according to whether the
selection for [EMPTY MODE] under [INK CONTROL] is set to [CONT.] or to [STOP]. (The default setting is [STOP].)
When Set to [STOP] (Pause)
[STOP] causes operation to pause immediately when ink needs to be replaced. Printing is resumed by replacing the cartridge.
Note, however, that colors of an image in progress may no longer match perfectly. Before you perform lengthy printing, replace
with ink cartridges that contain enough ink.
When Set to [CONT.] (Continue Printing)
Select this when ink cannot be replaced immediately while printing in progress, such as during unattended operation at night.
When the machine is set to [CONT.], an alarm sounds approximately 1 m
2
before ink runs out, but printing continues without
pausing. Because printing continues with only a small amount or remaining ink, the printed ink may be faint. As a general
guide, about 1 m
2
of printing is possible with the remaining ink, but the amount of ink used varies greatly depending on the
image. Printing can be continued only for the data for which printing is currently in progress. The machine stops when it
finishes outputting one image.
When a cartridge runs out of ink,
its number and "_" flash.
Remove an ink cartridge gently. Sudden movement when
removing may cause ink to be spilled.
- USER’S MANUAL 1
- For the USA 2
- For Canada 2
- Contents 3
- NERGY STAR 5
- Features of the SP-300 6
- To Ensure Safe Use 7
- Avis sur les avertissements 12
- À propos des symboles 12
- 1. Getting Started 17
- 1-1 Checking Accessories 18
- 1-2 Names and Functions 19
- 1. Getting Started 20
- 1-3 Assembling and Installing 21
- Step 1: Assemble the Stand 22
- Step 7: Fill Ink 30
- Filling Ink 31
- Step 9: Install the Blade 33
- 2. Basic Operation 35
- Switching On the Power 36
- 2-2 Menu Operations 38
- Basic Menu Operations 39
- 2-3 Loading Media 40
- Loading Sheet Media 43
- Types of Media Clamps 44
- Attaching the Media Clamps 44
- Removing the Media Clamps 45
- Using the Long Media Clamps 45
- Setting the Media Clamps 46
- 2-4 Heater Operation 47
- 3. Performing Output 49
- Setting Cutting Conditions 52
- 3-2 Performing Output 54
- 3-3 Separating the Media 56
- Stopping Printing or Cutting 57
- To Resume Printing or Cutting 57
- Setting the Start Location 61
- Feed Correction 62
- Bidirectional Correction 64
- Saving an Adjustment Value 66
- Loading an Adjustment Value 66
- Adjusting the Blade Extension 67
- Adjusting Automatically 68
- Adjusting Manually 69
- Printing with Crop Marks 70
- Aligning Automatically 71
- Aligning Manually 72
- 5. Maintenance 75
- Replacing an Ink Cartridge 77
- Cleaning the Printing Heads 78
- Before Starting Cleaning 80
- After Finishing Cleaning 84
- 5-3 Other Cleaning Tasks 85
- Replacing the Wiper 86
- How to Replace the Blade 88
- 5-6 When Moving the Unit 91
- 6-1 Menu Flowchart 94
- To the [CLEANING] menu 95
- To the [WIPER REPLACE] menu 95
- Main Menu 99
- 6. About the Menus 100
- Cutting Configuration Menu 101
- Heater Configuration Menu 102
- Language/unit Menu 102
- Maintenance Menu 102
- 7. What to Do If 103
- 7-1 What to Do If 104
- ADJ.] something other 105
- The Media Becomes Jammed 106
- 7-2 Responding to a Message 107
- 8. Appendix 109
- 8-1 Specifications 110
- 8-2 Usable Media 111
- 8-3 Printing or Cutting Area 112
- 8-4 About Blade Life 114
- R3-031201 115
Related products and manuals for Print & Scan Roland VS-300
Print & Scan Roland SJ-740 User Manual
(128 pages)
(128 pages)
Print & Scan Roland PNC-900 User Manual
(31 pages)
(31 pages)
Print & Scan Roland PC-600 User Manual
(6 pages)
(6 pages)
Print & Scan Roland SJ-500 User Manual
(26 pages)
(26 pages)
Print & Scan Roland SJ-740 User Manual
(97 pages)
(97 pages)
Print & Scan Roland Metaza MPX-80 User Manual
(120 pages)
(120 pages)
Print & Scan Roland Modela MDX-40 Specifications
(102 pages)
(102 pages)
Print & Scan Roland SJ-600 User Manual
(77 pages)
(77 pages)
Print & Scan Roland SJ-745EX User Manual
(4 pages)
(4 pages)
Print & Scan Roland CJ-540 User Manual
(124 pages)
(124 pages)
Print & Scan Roland FJ-400 User Manual
(2 pages)
(2 pages)
© 2020, manymanuals.com. All rights reserved. | 3.885 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals