Roland Prelude User Manual Page 62

  • Download
  • Add to my manuals
  • Print
  • Page
    / 112
  • Table of contents
  • TROUBLESHOOTING
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 61
62
A phaser that continues raising/lowering the frequency at which the
sound is modulated.
fig.MFX-14
This is an effect that applies amplitude modulation (AM) to the input
signal, producing bell-like sounds. You can also change the
modulation frequency in response to changes in the volume of the
sound sent into the effect.
fig.MFX-15
This is a ring modulator that uses a 16-step sequence to vary the
frequency at which modulation is applied.
fig.MFX-16
Cyclically modulates the volume to add tremolo effect to the sound.
fig.MFX-17a
14: INFINITE PHASER
Parameter Range Explanation
Mode 1, 2, 3, 4
Higher values will produce a
deeper phaser effect.
Speed -100– +100
Speed at which to raise or lower
the frequency at which the sound
is modulated
(+: upward / -: downward)
Resonance 0–127 Amount of feedback
Mix 0–127
Volume of the phase-shifted
sound
Pan L64–63R Panning of the output sound
Low Gain -15– +15 dB
Amount of boost/cut for the low-
frequency range
High Gain -15– +15 dB
Amount of boost/cut for the high-
frequency range
Level 0–127 Output volume
15: RING MODULATOR
Parameter Value Description
Frequency 0–127
Adjusts the frequency at which modulation is
applied.
Sens 0–127
Adjusts the amount of frequency modulation
applied.
Polarity UP, DOWN
Determines whether the frequency modula-
tion moves towards higher frequencies (UP)
or lower frequencies (DOWN).
Low Gain -15– +15 dB Gain of the low frequency range
High Gain -15– +15 dB Gain of the high frequency range
Balance
D100:0W–
D0:100W
Volume balance between the direct sound
(D) and the effect sound (W)
Level 0–127 Output level
Infinite Phaser 2-Band EQ
L in
R in
L out
R out
Pan R
Pan L
L in
R in
L out
R out
Ring Mod
2-Band EQ
2-Band EQ
Ring Mod
16: STEP RING MODULATOR
Parameter Range Explanation
Step 01–16 0–127
Frequency of ring modulation at
each step
Rate 0.05–10.00 Hz, note
Rate at which the 16-step sequence
will cycle
Attack 0–127
Speed at which the modulation fre-
quency changes between steps
Low Gain -15– +15 dB
Amount of boost/cut for the low-
frequency range
High Gain -15– +15 dB
Amount of boost/cut for the high-
frequency range
Balance D100:0W–D0:100W
Volume balance of the original
sound (D) and effect sound (W)
Level 0–127 Output volume
17: TREMOLO
Parameter Value Description
Mod Wave
TRI, SQR, SIN, SAW1,
SAW2
Modulation Wave
TRI: triangle wave
SQR: square wave
SIN: sine wave
SAW1/2: sawtooth wave
Rate 0.05–10.00 Hz, note Frequency of the change
Depth 0–127 Depth to which the effect is applied
Low Gain -15– +15 dB Gain of the low range
High Gain -15– +15 dB Gain of the high range
Level 0–127 Output Level
L in
R in
L out
R out
Step Ring Mod
2-Band EQ
2-Band EQ
Step Ring Mod
L in
R in
L out
R out
Tremolo
2-Band EQ
2-Band EQ
Tremolo
SAW1 SAW2
Prelude_e.book Page 62 Wednesday, January 14, 2009 2:18 PM
Page view 61
1 2 ... 57 58 59 60 61 62 63 64 65 66 67 ... 111 112

Comments to this Manuals

No comments