Roland RS-50 User Manual download pdf (Page 77)

Adding effects

Effects

22: TM CTRL DLY (Time Control Delay)

You can change the delay time in real time. Lengthening the delay

will lower the pitch, and shortening it will raise the pitch.

fig.MFX-22

23: 2V PCH SHIFT (2-Voice Pitch

Shifter)

A Pitch Shifter shifts the pitch of the direct sound. This 2-voice pitch

shifter has two pitch shifters, and can add two pitch shifted sounds

to the direct sound.

fig.MFX-23

HF Damp

200–8000 [Hz],

BYPASS

Adjusts the frequency above

which sound fed back to the ef-

fect will be cut.

If you do not want to cut the

high frequencies of the feed-

back, set this parameter to BY-

PASS.

Balance # D100:0W–

D0:100W

Adjusts the volume balance be-

tween the direct sound and the

delay sound.

With a setting of D100:0W only the

direct sound will be output, and

with a setting of D0:100W only the

delay sound will be output.

Level 0–127 Adjusts the output level.

Parameter

Value Description

Delay #

0–840 [ms] Adjusts the time delay from the

direct sound until when each de-

lay sound is heard.

Feedback # -98– +98 [%] Adjusts the proportion (%) of

the delay sound that is fed back

into the effect.

Negative (-) settings will invert

the phase.

Acceleration 0–15 This parameter adjusts the time

over which the Delay Time will

change from the current setting

to a newly specified setting.

The rate of change for the Delay

Time directly affects the rate of

pitch change.

HF Damp 200–8000 [Hz],

BYPASS

Adjusts the frequency above

which sound fed back to the ef-

fect will be cut.

If you do not want to cut the

high frequencies of the feed-

back, set this parameter to BY-

PASS.

Pan L64–63R Adjusts the stereo location of the

delay sound.

L64 is far left, 0 is center, and

63R is far right.

Low Gain -15– +15 [dB] Adjusts the gain of the low fre-

quency.

High Gain -15– +15 [dB] Adjusts the gain of the high fre-

quency.

Parameter

Value Description

L in

R in

L out

R out

2-Band

Balance W

Balance D

2-Band

Feedback

Time Control Delay

Balance

D100:0W–

D0:100W

Adjusts the volume balance be-

tween the direct sound and the

delay sound.

With a setting of D100:0W only the

direct sound will be output, and

with a setting of D0:100W only the

delay sound will be output.

Level 0–127 Adjusts the output level.

Parameter

Value Description

Mode

1, 2, 3, 4, 5 Higher settings of this parame-

ter will result in slower re-

sponse, but steadier pitch.

Coarse A #1 -24– +12 [semi] Adjusts the pitch of Pitch Shift A

in semitone steps (-2- +1 oc-

taves).

Coarse B #2 -24– +12 [semi] Adjusts the pitch of Pitch Shift B

in semitone steps (-2- +1 oc-

taves).

Fine A #1 -100– +100

[cent]

Makes fine adjustments to the

pitch of Pitch Shift A in 2-cent

steps (-100- +100 cents).

One cent is 1/100th of a semi-

tone.

Fine B #2 -100– +100

[cent]

Makes fine adjustments to the

pitch of Pitch Shift B in 2-cent

steps (-100- +100 cents).

One cent is 1/100th of a semi-

tone.

Pre Delay A 0–500 [ms] Adjusts the time delay from

when the direct sound begins

until the Pitch Shift A sound is

heard.

Pre Delay B 0–500 [ms] Adjusts the time delay from

when the direct sound begins

until the Pitch Shift A sound is

heard.

Pan A L64–63R Adjusts the stereo location of the

Pitch Shift A sound.

L64 is far left, 0 is center, and

63R is far right.

Pan B L64–63R Adjusts the stereo location of the

Pitch Shift B sound.

L64 is far left, 0 is center, and

63R is far right.

Parameter

Value Description

L in

R in

L out

R out

2Voice Pitch Shifter

Level Balance A

Balance W

Balance D

Balance W

Balance D

Level Balance B

PanB R

PanA L

PanA R

PanB L

RS-50_e3.book 77 ページ２００３年１１月７日　金曜日　午後７時１分

1 2 ... 72 73 74 75 76 77 78 79 80 81 82 ... 131 132

Comments to this Manuals

No comments

Roland RS-50 User Manual Page 77

Comments to this Manuals

Related products and manuals for Musical Instruments Roland RS-50