Roland SYS-553 Owner's Manual Page 16
- Page / 149
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
16
Introduction
Introduction
The M-200i has an internal lithium battery that backs up the clock
function and the mixer settings. If this battery runs down, the
clock function and the feature that provides for the
reinstatement of the mixer settings that existed prior to
switching off the power will no longer operate correctly. If a
popup message recommending that you replace the battery
appears when you turn on the power, replace the battery as
described in the following procedure.
l Use only the specified type (model no. CR2032)
of lithium batteries (p. 16). Be sure to insert it as
directed (to ensure correct polarity).
l Used lithium batteries must be disposed of in
compliance with whatever regulations for their
safe disposal that may be observed in the
region in which you live.
1.
Back up the M-200i’s mixer settings to USB memory (p.
82).
Data for connection to a Wireless LAN router using the LAN
or WIRELESS LAN function cannot be backed up to USB
memory. After completing the operation, connect to the
Wireless LAN router again (p. 103).
2.
Switch off the M-200i’s power, and disconnect the power
cord from the AC outlet.
3.
Remove the two screws that fasten the battery cover as
shown in the illustration, and detach the battery cover.
fig.battery-panel1.eps
4.
Remove the old battery, and insert the new battery.
When removing, hook nail onto upperside of the battery.
Use care, as some of the metal edges may be sharp.
5.
Attach the battery cover as shown in the illustration, and
fasten it using the two screws you removed in step 3.
ig.battery-panel2.eps
6.
Turn on the power of the M-200i, and set the date and
time (p. 112).
7.
Load the previously saved settings (MIXER PARAMETER,
SYSTEM SETTING) from the USB memory to which you
backed up the data in step 1. (p. 81)
The M-200i can use USB memory to store and read a variety of
data.
• Record and play WAV files using the USB Memory Recorder
• Back up and recover internal mixer data
Carefully insert the USB memory until it is firmly in place.
When the access lamp of USB memory is lit or blinking,
please do not remove the USB memory. This might cause
some damage to the data of the USB memory or deficit.
USB memory used with the USB Memory Recorder must support
USB 2.0 (Hi-speed).
About the internal lithium
battery
About USB memory
M-200i_e.book 16 ページ ２０１３年６月２８日 金曜日 午後１時２７分
- Owner’s Manual 1
- ALWAYS OBSERVE THE FOLLOWING 3
- IMPORTANT NOTES 6
- Contents 8
- Introduction 11
- Placement 13
- Turning the power on/off 15
- About the internal lithium 16
- About USB memory 16
- Explanation of the panels 17
- PHONES LEVEL knob 21
- iPad connection area 21
- Rear panel 22
- Basic operation 26
- Screen operations 27
- List operations 28
- Library operations 30
- Editing a name 33
- Peak clear 33
- About the input channels 34
- Accessing the CHANNEL EDIT 35
- Input channel operations 36
- CHANNEL FUNCTION screen 37
- AUX, MTX, MAIN operations 39
- GATE/EXPANDER screen 44
- GATE FUNCTION screen 47
- COMPRESSOR/LIMITER screen 49
- COMPRESSOR screen 50
- LIMITER screen 53
- LIMITER FUNCTION screen 54
- 4-BAND EQ 55
- EQ FUNCTION screen 56
- AUX/MTX send 57
- SENDS screen 58
- SENDS FUNCTION screen 58
- Metering 59
- DCA groups 60
- DCA GROUP FUNCTION screen 61
- Mute groups 62
- About effects 64
- EFFECTS screen 65
- EFFECTS FUNCTION screen 66
- Effect input/output settings 66
- Inserting an EXT FX into a 68
- Editing effect parameters 69
- Using the effect library 70
- About GEQs 71
- Editing GEQ parameters 72
- Scene memory 74
- USB memory recorder 77
- RECORDER FUNCTION screen 78
- Using the USB memory recorder 78
- SETUP screen 80
- Saving and loading mixer 81
- Locking the console 83
- Viewing system information 83
- Managing USB memory 85
- Input/output patchbay 86
- Patchbay operations 87
- Talkback 89
- Oscillator 91
- Monitor/Solo 92
- Using the monitor 93
- Using solo 93
- User Preference settings 94
- Editing the user buttons 95
- Selecting the Home screen 95
- REAC applications 96
- REAC connection examples 97
- REAC settings 98
- Network functions 100
- Network settings 100
- LAN setting 101
- Restrictions 104
- Connecting using WPS 104
- MAC ADDRESS 105
- Connection status 105
- Connection infomation 105
- IP ADDRESS 105
- Remote functions 106
- Accessing the REMOTE screen 107
- MIDI settings 108
- USB MIDI settings 109
- V-LINK settings 110
- RS-232C settings 110
- System settings 111
- Date&time setting 112
- Other settings 113
- Appendix 115
- Error message list 116
- Troubleshooting 117
- Pin configuration diagrams 119
- Main specifications 121
- Dimensions 124
- Effect types 125
- St.REVERB (Stereo Reverb) 126
- REVERB+GATE 128
- Delay A/B 130
- Modulation 134
- Channel strip 136
- Pitch shift 138
- Roland vintage effects 140
- The amount of RAM access for 141
- Apparatus containing 142
- Lithium batteries 142
- DECLARATION OF CONFORMITY 143
- Block Diagram 147
Related products and manuals for Sequencer Roland SYS-553
Sequencer Roland D2 Owner's Manual
(116 pages)
(116 pages)
Sequencer Roland SYS-553 Owner's Manual
(84 pages)
(84 pages)
Sequencer Roland TD-30 Owner's Manual
(160 pages)
(160 pages)
Sequencer Roland MC-307 Owner's Manual
(216 pages)
(216 pages)
© 2020, manymanuals.com. All rights reserved. | 1.622 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals