Roland SYS-553 Owner's Manual Page 72
- Page / 149
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
72
Effects, GEQ, External effects
Effects, GEQ, External effects
1.
Access the GEQ screen
2.
Move the cursor to the EDIT button for the desired GEQ
among “GEQ1-4“ and press [ENTER].
The GEQ1-4 EDIT screen is displayed.
GEQ faders
For each frequency band, these adjust the amount of boost
or cut in a range of -15.0 dB to +15.0 dB.
Use the left and right cursor buttons to select the desired
fader.
The value of the fader you operate is shown above the faders
of the GEQ.
Noise may occur when you operate the GEQ faders, but this is
not a malfunction. While using the top panel faders to control
the GEQ, [MUTE] buttons flash for faders whose position is
anything other than 0.0dB. Pressing a flashing [MUTE] resets the
fader to the 0.0-dB position.
1.
Access the GEQ EDIT screen for the desired channel.
2.
Press [FUNC] to access the GEQ EDIT FUNCTION screen.
The operations available at the GEQ EDIT FUNCTION screen are as
follows:
For information on COPY, PASTE, UNDO, LIBRARY go to “Basic
operation,“ and refer to “Copy“ (p. 28), “Paste“ (p. 29), “Undo“(p.
29), “Library“ (p. 30).
Editing GEQ parameters
GEQ EDIT screen
1
GEQ EDIT FUNCTION screen
GEQ ON FADER
When this is set to ON, you can controll a GEQ
using the top-panel faders (p. 73).
0.5dB STEP When this is set to ON, you can operate the GEQ
fader in steps of 0.5 dB.
SOURCE This sets the insert channel for the specified GEQ.
BYPASS This turns bypass on/off for the specified GEQ.
When these are on, the input signal will be “thru-
ed” to the output.
LINK This links the parameters between GEQ 1 and 2 (or
GEQ 3 and 4).
FLAT This sets the 31-band GEQ to a flat response.
COPY Copies GEQ settings to the clipboard.
PASTE When GEQ settings have been copied to the
clipboard, this pastes the settings from the
clipboard.
UNDO This undoes the last-performed parameter paste
operation. It is not displayed when there is no
action to undo.
LIBRARY Accesses the FX LIBRARY screen.
M-200i_e.book 72 ページ ２０１３年６月２８日 金曜日 午後１時２７分
- Owner’s Manual 1
- ALWAYS OBSERVE THE FOLLOWING 3
- IMPORTANT NOTES 6
- Contents 8
- Introduction 11
- Placement 13
- Turning the power on/off 15
- About the internal lithium 16
- About USB memory 16
- Explanation of the panels 17
- PHONES LEVEL knob 21
- iPad connection area 21
- Rear panel 22
- Basic operation 26
- Screen operations 27
- List operations 28
- Library operations 30
- Editing a name 33
- Peak clear 33
- About the input channels 34
- Accessing the CHANNEL EDIT 35
- Input channel operations 36
- CHANNEL FUNCTION screen 37
- AUX, MTX, MAIN operations 39
- GATE/EXPANDER screen 44
- GATE FUNCTION screen 47
- COMPRESSOR/LIMITER screen 49
- COMPRESSOR screen 50
- LIMITER screen 53
- LIMITER FUNCTION screen 54
- 4-BAND EQ 55
- EQ FUNCTION screen 56
- AUX/MTX send 57
- SENDS screen 58
- SENDS FUNCTION screen 58
- Metering 59
- DCA groups 60
- DCA GROUP FUNCTION screen 61
- Mute groups 62
- About effects 64
- EFFECTS screen 65
- EFFECTS FUNCTION screen 66
- Effect input/output settings 66
- Inserting an EXT FX into a 68
- Editing effect parameters 69
- Using the effect library 70
- About GEQs 71
- Editing GEQ parameters 72
- Scene memory 74
- USB memory recorder 77
- RECORDER FUNCTION screen 78
- Using the USB memory recorder 78
- SETUP screen 80
- Saving and loading mixer 81
- Locking the console 83
- Viewing system information 83
- Managing USB memory 85
- Input/output patchbay 86
- Patchbay operations 87
- Talkback 89
- Oscillator 91
- Monitor/Solo 92
- Using the monitor 93
- Using solo 93
- User Preference settings 94
- Editing the user buttons 95
- Selecting the Home screen 95
- REAC applications 96
- REAC connection examples 97
- REAC settings 98
- Network functions 100
- Network settings 100
- LAN setting 101
- Restrictions 104
- Connecting using WPS 104
- MAC ADDRESS 105
- Connection status 105
- Connection infomation 105
- IP ADDRESS 105
- Remote functions 106
- Accessing the REMOTE screen 107
- MIDI settings 108
- USB MIDI settings 109
- V-LINK settings 110
- RS-232C settings 110
- System settings 111
- Date&time setting 112
- Other settings 113
- Appendix 115
- Error message list 116
- Troubleshooting 117
- Pin configuration diagrams 119
- Main specifications 121
- Dimensions 124
- Effect types 125
- St.REVERB (Stereo Reverb) 126
- REVERB+GATE 128
- Delay A/B 130
- Modulation 134
- Channel strip 136
- Pitch shift 138
- Roland vintage effects 140
- The amount of RAM access for 141
- Apparatus containing 142
- Lithium batteries 142
- DECLARATION OF CONFORMITY 143
- Block Diagram 147
Related products and manuals for Sequencer Roland SYS-553
Sequencer Roland D2 Owner's Manual
(116 pages)
(116 pages)
Sequencer Roland SYS-553 Owner's Manual
(84 pages)
(84 pages)
Sequencer Roland TD-30 Owner's Manual
(160 pages)
(160 pages)
Sequencer Roland MC-307 Owner's Manual
(216 pages)
(216 pages)
© 2020, manymanuals.com. All rights reserved. | 3.548 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals