Roland SYS-553 Owner's Manual Page 93
- Page / 149
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
93
Monitor/Solo
Monitor/Solo
1.
Access the MONITOR FUNCTION screen.
2.
Move the cursor to the MONITOR SOURCE and press
[ENTER] to access the MONITOR SOURCE screen.
3.
Select the monitor source and press [ENTER].
The monitor signal is output from the output jacks to which
MONITOR OUT L/R are patched, and from the PHONES jack.
4.
Use “MONITOR LEVEL“ or the “PHONES LEVEL knob“ to
adjust the output level of the monitor.
1.
At the MONITOR FUNCTION screen, adjust the “SOLO
LEVEL“ setting
2.
At the top panel, press [SOLO] for the desired channel.
The signal of that channel is sent to solo buses and output
from the output jacks to which MONITOR OUT L/R are
patched and from the PHONES jack.
3.
At the MONITOR section, use the “LEVEL knob“ or the
“PHONES LEVEL knob“ to adjust the monitor output
level.
INPUT AFL
This selects the point from the signal is sent from
CH1 through 32 to solo. If this is on, the post-pan
signal of the channel is sent. If this is off, the pre-
fader signal is sent.
OUTPUT AFL This selects the point from which the signal is sent
from MAIN, AUX, or MTX to solo. If this is on, the post-
fader signal of the channel is sent. If this is off, the
pre-fader signal is sent.
SOLO FOLLOWS
SENDS ON FADER
If this is on, the solo of the AUX/MTX is turned on in
tandem with “SENDS ON FADER.“ When the “SENDS
ON FADER“ mode is turned off, solo is turned off.
Using the monitor
By default, MONITOR L/R is patched to ASSIGNABLE
OUTPUT 9/10. You can use the output patchbay to
change the output destination. For details, refer to
“Editing the output patching” (p. 88).
Using solo
Solo is set to have the following priorities:
Solo operates under the following rules;
• Turning on a higher-priority solo temporary replaces
lower-priority solos. Operation returns to the lower-
priority solos when the higher-priority solo is cleared.
• Turning on a lower-priority solo clears higher-priority
solos.
(High) 4 Key-in solo
Priority
3 CH
2 DCA solo
(Low) 1 MAIN, AUX, MTX
M-200i_e.book 93 ページ ２０１３年６月２８日 金曜日 午後１時２７分
- Owner’s Manual 1
- ALWAYS OBSERVE THE FOLLOWING 3
- IMPORTANT NOTES 6
- Contents 8
- Introduction 11
- Placement 13
- Turning the power on/off 15
- About the internal lithium 16
- About USB memory 16
- Explanation of the panels 17
- PHONES LEVEL knob 21
- iPad connection area 21
- Rear panel 22
- Basic operation 26
- Screen operations 27
- List operations 28
- Library operations 30
- Editing a name 33
- Peak clear 33
- About the input channels 34
- Accessing the CHANNEL EDIT 35
- Input channel operations 36
- CHANNEL FUNCTION screen 37
- AUX, MTX, MAIN operations 39
- GATE/EXPANDER screen 44
- GATE FUNCTION screen 47
- COMPRESSOR/LIMITER screen 49
- COMPRESSOR screen 50
- LIMITER screen 53
- LIMITER FUNCTION screen 54
- 4-BAND EQ 55
- EQ FUNCTION screen 56
- AUX/MTX send 57
- SENDS screen 58
- SENDS FUNCTION screen 58
- Metering 59
- DCA groups 60
- DCA GROUP FUNCTION screen 61
- Mute groups 62
- About effects 64
- EFFECTS screen 65
- EFFECTS FUNCTION screen 66
- Effect input/output settings 66
- Inserting an EXT FX into a 68
- Editing effect parameters 69
- Using the effect library 70
- About GEQs 71
- Editing GEQ parameters 72
- Scene memory 74
- USB memory recorder 77
- RECORDER FUNCTION screen 78
- Using the USB memory recorder 78
- SETUP screen 80
- Saving and loading mixer 81
- Locking the console 83
- Viewing system information 83
- Managing USB memory 85
- Input/output patchbay 86
- Patchbay operations 87
- Talkback 89
- Oscillator 91
- Monitor/Solo 92
- Using the monitor 93
- Using solo 93
- User Preference settings 94
- Editing the user buttons 95
- Selecting the Home screen 95
- REAC applications 96
- REAC connection examples 97
- REAC settings 98
- Network functions 100
- Network settings 100
- LAN setting 101
- Restrictions 104
- Connecting using WPS 104
- MAC ADDRESS 105
- Connection status 105
- Connection infomation 105
- IP ADDRESS 105
- Remote functions 106
- Accessing the REMOTE screen 107
- MIDI settings 108
- USB MIDI settings 109
- V-LINK settings 110
- RS-232C settings 110
- System settings 111
- Date&time setting 112
- Other settings 113
- Appendix 115
- Error message list 116
- Troubleshooting 117
- Pin configuration diagrams 119
- Main specifications 121
- Dimensions 124
- Effect types 125
- St.REVERB (Stereo Reverb) 126
- REVERB+GATE 128
- Delay A/B 130
- Modulation 134
- Channel strip 136
- Pitch shift 138
- Roland vintage effects 140
- The amount of RAM access for 141
- Apparatus containing 142
- Lithium batteries 142
- DECLARATION OF CONFORMITY 143
- Block Diagram 147
Related products and manuals for Sequencer Roland SYS-553
Sequencer Roland D2 Owner's Manual
(116 pages)
(116 pages)
Sequencer Roland SYS-553 Owner's Manual
(84 pages)
(84 pages)
Sequencer Roland TD-30 Owner's Manual
(160 pages)
(160 pages)
Sequencer Roland MC-307 Owner's Manual
(216 pages)
(216 pages)
© 2020, manymanuals.com. All rights reserved. | 0.553 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals