Roland XC-540MT User Manual Page 41
- Page / 172
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Chapter 2 Basic Operation
2-3 Settings for the Media Heating System
39
Chapter 2 Basic Operation
Use to make the setting.
Press to enable the setting.
Press .
Press to go back to the original screen.
By default, simply switching on the power does not make the machine warm up to the preset tem-
perature. Pressing to make the light come on makes the system warm up to the preset
temperature.
General Guide for the Preset Temperatures
The optimal temperature for the media heating system varies according to such factors as the type of me-
dia and dierences in the print mode. Use the following as a general guide and adjust accordingly.
General Guide for Adjustment
Preheater
Set this to a temperature that is the same as or lower than the temperature of the print heater.
You use the preheater mainly to heat media gradually. This is because media becomes more likely to
shrink or wrinkle if heated suddenly.
Print heater
You use this mainly to improve ink adhesion and inhibit smudging.
If the ink forms lumps or smudges, raise the temperature. Note, however, that a temperature that is too
high may degrade the media or cause it to wrinkle.
Dryer
When ink drying is poor, raise the temperature. Note, however, that a temperature that is too high may
degrade the media or cause it to wrinkle.
The relationship between the print mode and temperature
If smudging or poor drying occur even after raising the temperature, try using a print mode oering
higher image quality. Conversely, when you want to use a faster print mode, raise the temperature.
Amount of ink
When you change the amount of ink using the settings for your software RIP, adjusting this may yield
better results. If problems such as smudging persist even after raising the temperature, try reducing
the amount of ink.
Use at an ambient temperature of 20 to 32ºC (68 to 90ºF).
If the machine is used at an ambient temperature lower than 20ºC (68ºF), then depending on the type or
width of the media, wrinkling or temperature-caused unevenness may occur. To obtain stable printing
results, the machine should be used at an ambient temperature of 20 to 32ºC (68 to 90ºF).
DRYER 50
5550
W 1346mm
SETUP SHEET
ROLL
- USER'S MANUAL 1
- Contents 3
- To Ensure Safe Use 7
- Warning Labels 13
- Avis sur les avertissements 14
- ATTENTION 14
- PRUDENCE 14
- À propos des symboles 14
- Printer Unit 22
- Ink Cartridges 23
- Chapter 1 25
- Introduction 25
- 1-1 Features of the Machine 26
- 1-2 Part Names and Functions 27
- Operation Panel 29
- Media Take-up System 30
- Chapter 2 31
- Basic Operation 31
- WARNING 32
- The Power-saving Feature 33
- How to Load Media 34
- Align the media 35
- OK Not OK 36
- Install the media clamps 37
- Close the front cover 37
- Press 37
- PINCHROLL ERROR 38
- INVALID *** POS 38
- How to Cut Off Media 39
- General Guide for Adjustment 41
- 2-4 Starting Output 43
- Printing Tests and Cleaning 44
- How to Perform Cleaning 45
- 2-5 If Ink Runs Out 47
- If Ink Runs Out 48
- Chapter 3 51
- Using the Cutting 51
- 3-1 Performing Cutting 52
- Performing a Cutting Test 53
- Important 54
- Printing with Crop Marks 55
- Aligning Manually and Cutting 58
- Set the align points 59
- Chapter 4 61
- Operation of the Me 61
- 4-1 The Take-up System 62
- About the Paper Tube 63
- 4-2 Using the Take-up System 64
- ■ Take-up with outward curl 65
- ■ Take-up with inward curl 65
- Press 66
- ■ Take-up with outward curl 67
- How to Remove Taken-up Media 68
- Chapter 5 69
- Maintenance and 69
- Adjustment 69
- Disposing of Discharged Ink 70
- CAUTION 71
- Cleaning 72
- Daily Care and Maintenance 73
- Periodic Care and Maintenance 73
- MEDIUM CL 74
- A B C 74
- A C 74
- Start cleaning 75
- SUB MENU 77
- CLEANING 79
- CLOSE MAINTE 79
- NANCE COVER 79
- Replacing the Wipers 80
- Replacing the Blade 83
- Replace the separating knife 85
- Keep Performing Maintenance 87
- Alarm Feature 87
- 5-6 When Moving the Unit 88
- Chapter 6 91
- Feature Reference 91
- Using Transparent Media 96
- Printing Hard-to-dry Media 96
- FULL WIDTH S 98
- How to Load Sheet Media 100
- EMPTY MODE 101
- INTERVAL 102
- Deactivating the Sleep Mode 103
- FEED FOR DRY 104
- Procedure 105
- Description 105
- Default Setting 105
- W 1346mm 107
- SETUP SHEET 107
- ROLL 107
- FEED SETTING 109
- 0.00% 0.00% 109
- SCAN SETTING 109
- A. The shape is correct 111
- B. The corners are rounded 111
- CUTTING PRIOR 112
- COMMAND MENU 112
- Print a test pattern 113
- F :- 0.30 - 0.30mm 120
- S : 0.00 - 0.20mm 120
- CUTTING MENU 122
- HEATER MENU 127
- OPTION DRYER 127
- Loading a Saved Preset 131
- Assigning a Name to a Preset 131
- IP ADDRESS 133
- Viewing the Network Settings 134
- Printing a System Report 135
- 6-13 Performing Maintenance 136
- 6-14 Menu List 137
- 6-12 Menu List 138
- Chapter 6 Feature Reference 138
- (*1) XC-540 only 139
- Language and Unit Menu 142
- Cleaning Menu 142
- Heater Conguration Menu 142
- Cutting Conguration Menu 143
- Chapter 7 145
- What to Do If 145
- Is media loaded? 147
- Colors Are Unstable or Uneven 149
- 7-3 The Media Jams 151
- The Media Jams 151
- Is media feed unstable? 152
- Media Wrinkles or Shrinks 153
- Media Feed Is Not Straight 153
- Media Feed Is Not Smooth 153
- What to Do First 154
- 7-7 If a Message Appears 155
- Detection" 156
- Chapter 8 159
- Appendix 159
- 8-1 Usable Media 160
- Acceptable Media Width 161
- 8-2 Printing or Cutting Area 162
- 8-3 About the Blade 164
- 8-5 Specications 166
- During standby 167
- Temperature 168
- Humidity(%) 168
- Chapter 8 Appendix 169
- R1-090918 172
Related products and manuals for Print & Scan Roland XC-540MT
Print & Scan Roland XR-640 Setup Guide
(60 pages)
(60 pages)
Print & Scan Roland COLORCHOICE User's Guide
(50 pages)
(50 pages)
Print & Scan Roland FJ-40 Specifications
(28 pages)
(28 pages)
Print & Scan Roland CJ-540 User Manual
(120 pages)
(120 pages)
Print & Scan Roland XC-540MT User Manual
(19 pages)
(19 pages)
Print & Scan Roland PC-12 User Manual
(49 pages)
(49 pages)
Print & Scan Roland VS-640i Setup Guide
(52 pages)
(52 pages)
Print & Scan Roland MPX-60 User Manual
(68 pages)
(68 pages)
Print & Scan Roland CX-300 User Manual
(102 pages)
(102 pages)
Print & Scan Roland VS-540 Setup Guide
(56 pages)
(56 pages)
Print & Scan Roland LEC-300A User Manual
(2 pages)
(2 pages)
Print & Scan Roland RA-640 Specifications
(50 pages)
(50 pages)
Print & Scan Roland SJ-745EX User Manual
(52 pages)
(52 pages)
Print & Scan Roland CX-400 User Manual
(21 pages)
(21 pages)
Print & Scan Roland PC-12 User Manual
(2 pages)
(2 pages)
Print & Scan Roland SJ-540 User Manual
(26 pages)
(26 pages)
Print & Scan Roland PC-12 Specifications
(97 pages)
(97 pages)
© 2020, manymanuals.com. All rights reserved. | 0.561 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals