Roland VS-1824 Owner's Manual Page 81
- Page / 140
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
81
Algorithm List
Algorithm List
High Rel (High Release) 50 ms–5.000 s Sets the time until when the High frequency band expander stops working
after the input level exceeds the High threshold level.
Cmp (Compressor):Compresses the entire output signals when the input volume exceeds a specified value.
SW (Switch) On, Off Turns the compressor on or off.
Low Thre (Low Threshold) -24–0 dB
Sets the volume at which the compressor for the low frequency band starts working.
Low Ratio (Low Raito) 1:1.0–1:16, 1:INF Sets the ratio at which the output in the low frequency band is suppressed
when the input level has exceeded the low threshold level.
Low Atck (Low Attack) 0–100 ms Sets the time until when the low frequency band compressor starts working
after the input level has exceeded the low threshold level.
Low Rel (Low Release) 50 ms–5.000 s Sets the time until when the low frequency band compressor stops working
after the input level has dropped below the low threshold level.
Mid Thre (Middle Threshold) -24–0 dB Sets the volume at which the compressor in the middle frequency band
starts working.
Mid Ratio (Middle Ratio) 1:1.0–1:16, 1:INF Sets the ratio at which the output in the middle frequency band is
suppressed when the input level has exceeded the middle threshold level.
Mid Atck (Middle Attack) 0–100 ms Sets the time until when the middle frequency band compressor starts
working after the input level has exceeded the middle threshold level.
Mid Rel (Middle Release) 50 ms–5.000 s Sets the time until when the middle frequency band compressor stops
working after the input level has dropped below the middle threshold level.
High Thre (High Threshold) -24–0 dB
Sets the volume at which the compressor for the High frequency band starts
working.
High Raito (High Ratio) 1:1.0–1:16, 1:INF Sets the ratio at which the output in the High frequency band is suppressed
when the input level has exceeded the High threshold level.
High Atck (High Attack) 0–100 ms Sets the time until when the High frequency band compressor starts
working after the input level has exceeded the High threshold level.
High Rel (High Release) 50 ms–5.000 s Sets the time until when the High frequency band compressor stops working
after the input level has dropped below the High threshold level.
Mix (Mixer): Adjusts the volume by frequency band.
Low Level (Low Level) -80– +6 dB Sets the volume in the low frequency band after passing through the
expander and compressor.
Mid Level (Middle Level) -80– +6 dB Sets the middle frequency band volume after passing through the expander
and compressor.
High Level (High Level) -80– +6 dB Sets the volume in the High frequency band after passing through the
expander and compressor.
Lmt (Limiter): Prevents distortion by suppressing signals at High levels.
Sw (Switch) On, Off Turns the limiter on or off.
Thresh (Threshold) -24–0 dB Sets the volume at which the limiter starts working.
Attack (Attack) 0–100 ms Sets the time until when the limiter starts working after the input level has
exceeded threshold level.
Release (Release) 50 ms–5.000 s Sets the time until when the limiter stops working after the input level drops
below the threshold level.
Out (Output): Provides settings concerning overall output.
SoftClip (Soft Clip) On, Off Suppresses conspicuous distortion that may occur when the effect of
compressor/limiter has been applied excessively.
Dither (Dither) Off, 8–24 bit Smoothes the transition where the sound disappears.
Level (Level) -80– +6 dB Sets the overall volume after passing through the limiter.
With Compressor, the level is automatically adjusted to the optimal with the settings for Threshold (Thres) and
Raito (Ratio). Setting Attack (Atck) to a relatively long time may cause distortion. For this reason, a margin of -6
dB is provided. Adjust the Mixer (Mix) level as required.
*1: If Low Type (Lo Type) or High Type (Hi Type) is set to “Shlv (Shlving Type),” the setting for Lo Q or High Q is
invalid.
- Appendices 1
- About MIDI 3
- About SCSI 4
- Troubleshooting 5
- Disk drive problems 6
- Internal Effects 7
- CD-RW Drive Problems 7
- MIDI Devices Problems 7
- Other problems 8
- Error Messages 10
- Glossary 12
- Shortcut Key Operations 14
- ■ LOCATOR/SCENE buttons 15
- ■ FUNCTION buttons 15
- Parameter List 16
- ■ Master Block [MASTER] 17
- Preset Patch List 20
- Stereo Delay Chorus 21
- ■ Reverb2 (20 presets) 22
- ■ Mic Modeling (22 presets) 22
- Algorithm List 25
- (Compressor-related) 25
- Sound types 26
- Reverb sound quality 26
- Delay repetition 28
- Setting up pitch 32
- Tips for using Vocoder 34
- What is RSS? 35
- Continued 35
- For Stereo Speakers 36
- Delay RSS 37
- Chorus RSS 38
- GuitarMulti 1–3 39
- Vocal Multi 42
- St Phaser (Stereo Phaser) 47
- St Flnger (Stereo Flanger) 49
- Reverb sound 52
- MultiTapDly (Multi-Tap Delay) 54
- Stereo Multi 56
- Reverb 2 58
- 1, 2, 3, 4, 1+4, 2+4, 3+4 60
- Creating lo-fi sounds 61
- Cutting noise 62
- Preventing howling 63
- Hum Canceler 64
- Vocal Canceler 65
- Voice Transformer 67
- Vocoder 2 (19) 69
- Mic Converter A 71
- Mic Converter B 71
- Muting the bass 73
- Muting vocals 73
- Muting noise 73
- TapeEcho201 74
- Output L 74
- Output R 74
- AnalogFlnger (Analog Flanger) 75
- AnalogPhaser 76
- Speaker Modeling 77
- Mastering Tool Kit 79
- 2. Data Transfer Address Map 98
- MIDI Implementation 100
- 3. MIDI Machine Control 123
- 4. Appendices 125
- Mix Offset Bal 127
- Mixer Section Block Diagram 128
- Master Block 129
- Track Sheet 130
- Track Sheet (2) 131
- Specifications 132
- ...MEMO 137
- Contents 139
Related products and manuals for Musical Instruments Roland VS-1824
(56 pages)
Musical Instruments Roland KR-3 Owner's Manual
(200 pages)
(200 pages)
Musical Instruments Roland FP-3 User Manual
(64 pages)
(64 pages)
© 2020, manymanuals.com. All rights reserved. | 0.173 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals