Roland SJ-600 User Manual Page 44
- Page / 116
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
2-3 Settings of Preheater, Print Heater and Dryer
42
Chapter 2 Operation
General Guide for the Preset Temperatures
The optimal temperature settings vary according to the type of media, differences in the print mode, and other
factors. Use the following as a general guide and adjust accordingly.
General Guide for Adjustment
Preheater
Set this to a temperature that is the same as or lower than the temperature of the print heater.
You use the preheater mainly to heat media gradually. This is because media becomes more likely to shrink or
wrinkle if heated suddenly.
Print heater
You use this mainly to improve ink adhesion and inhibit smudging.
If the ink forms lumps or smudges, raise the temperature. Note, however, that a temperature that is too high may
degrade the media or cause it to wrinkle.
Dryer
When ink drying is poor, raise the temperature. Note, however, that a temperature that is too high may degrade
the media or cause it to wrinkle.
The relationship between the print mode and temperature
If smudging or poor drying occur even after raising the temperature, try using a print mode offering higher image
quality. Conversely, when you want to use a faster print mode, raise the temperature.
Amount of ink
When you change the amount of ink using the settings for your RIP program, adjusting this may yield better
results. If problems such as smudging persist even after raising the temperature, try reducing the amount of ink.
Examples of Preset Temperatures
➢ These are only rough estimates. Make adjustments to match the media you're using.
➢ Using the heating devices does not necessarily make it possible to apply ink to every kind of media. Be sure to test
in advance.
➢ Results may vary greatly depending on the print mode and other factors. Make settings suited to the media.
➢ When suggested settings for temperature, print mode, and other values are given, use the suggested settings.
Media
Type: Scrim banner (PVC)
Thickness: 300 to 400 µm (12 to 16 mil)
Type: Marking film (PVC, with adhesive)
Thickness: 60 to 100 µm (2.5 to 4 mil, not including backing paper)
Temperature
Preheater: 45˚C (112˚F)
Print heater: 45˚C (112˚F)
Dryer: 50˚C (122˚F)
Preheater: 40˚C (104˚F)
Print heater: 40˚C (104˚F)
Dryer: 45˚C (112˚F)
- USER'S MANUAL 1
- For the USA 2
- For Canada 2
- Contents 3
- To Ensure Safe Use 6
- WARNING CAUTION 10
- Warning Labels 11
- ATTENTION 12
- PRUDENCE 12
- Printer unit 18
- Ink cartridges 18
- Chapter 1 19
- Introduction 19
- 1-1 Machine Features 20
- 1-2 Part Names and Functions 21
- Printer Control Panel 23
- Chapter 2 25
- Operation 25
- √ Main power switch 26
- The Power-saving Feature 27
- How to Load Media 28
- Switch off the power 32
- Open the cover 32
- Mount the roll shaft 32
- Chapter 2 Operation 35
- Feed unit 35
- Install the media clamps 40
- How to Cut Off Media 41
- Procedure 43
- General Guide for Adjustment 44
- 2-4 Starting Printing 45
- Printing Tests and Cleaning 46
- 2-5 If Ink Runs Out 47
- If Ink Runs Out 48
- Chapter 3 51
- Maintenance and 51
- Adjustment 51
- Disposing of Discharged Ink 52
- Cleaning 53
- Daily Care and Maintenance 54
- Periodic Care and Maintenance 54
- Start cleaning 55
- How to Perform Cleaning 57
- Replacing the Wipers 61
- Keep Performing Maintenance 63
- Alarm Feature 63
- Chapter 4 65
- Feature Reference 65
- Description 66
- Print a test pattern 71
- Enter the correction value 75
- Default Setting 76
- Using Transparent Media 77
- Printing Hard-to-dry Media 77
- Deactivating the Sleep Mode 82
- Printing a System Report 83
- The display is updated 86
- 4-8 Menu List 88
- Language and Unit Menu 92
- Cleaning and Maintenance Menu 92
- Heater Configuration Menu 92
- Chapter 5 93
- What to Do If 93
- Colors Are Unstable or Uneven 95
- 5-3 The Media Jams 97
- Media Wrinkles or Shrinks 99
- The Media Is Not Straight 99
- Media Feed Is Not Smooth 99
- What to Do First 100
- 5-7 If a Message Appears 101
- Chapter 6 105
- Specifications 105
- 6-1 Usable Media 106
- 6-2 Printing Area 107
- 6-4 Specifications 109
- R3-070201 116
Related products and manuals for Print & Scan Roland SJ-600
Print & Scan Roland VS-640i User Manual
(176 pages)
(176 pages)
Print & Scan Roland XR-640 User Manual
(80 pages)
(80 pages)
Print & Scan Roland PC-600 User Manual
(56 pages)
(56 pages)
Print & Scan Roland PNC-950 User Manual
(41 pages)
(41 pages)
Print & Scan Roland XR-640 User Manual
(4 pages)
(4 pages)
Print & Scan Roland LEC-540 Setup Guide
(64 pages)
(64 pages)
Print & Scan Roland LEC-540 User Manual
(2 pages)
(2 pages)
Print & Scan Roland RA-640 Specifications
(36 pages)
(36 pages)
Print & Scan Roland FJ-52 User Manual
(78 pages)
(78 pages)
Print & Scan Roland VS-640i User Manual
(9 pages)
(9 pages)
Print & Scan Roland LEC-300 Specifications
(56 pages)
(56 pages)
Print & Scan Roland CX-400 Specifications
(64 pages)
(64 pages)
Print & Scan Roland CX-400 User Manual
(24 pages)
(24 pages)
Print & Scan Roland LEC-300A Setup Guide
(68 pages)
(68 pages)
Print & Scan Roland SJ-600 User Manual
(10 pages)
(10 pages)
Print & Scan Roland PC-12 User Manual
(10 pages)
(10 pages)
Print & Scan Roland BN-20 User Manual
(2 pages)
(2 pages)
© 2020, manymanuals.com. All rights reserved. | 2.598 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals