Roland VersaCamm VP-540i Specifications Page 38
- Page / 136
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
2-2 Loading and Cutting Off Media
Chapter 2 Operation
37
Important Note When Using the Media Clamps
➢Set the media clamps at the correct locations. If they are not set at the correct locations, the media may catch,
preventing successful printing.
➢As printing proceeds, the media may move to the left or right and touch or come loose from the media clamps.
After about 1 m (3 ft.) of media has been fed, check the positioning of the media clamps. If the media looks like
it may come loose from the media clamps, adjust the positioning of the media clamps.
➢Moving a media clamp to the right edge of the platen as shown in the figure below may cause it to be hidden
by the cutting carriage and make it impossible to detach the media clamp without further action. If this
happens, first load the media, then lower the loading lever. After lights up, use to move the
cutting carriage to a location where it doesn’t obstruct the media clamp, then detach or move the media
clamp.
Position the pinch rollers over the grit rollers.
If the message shown in the figure appears when you close the front cover, check the positions of the pinch rollers and
the middle pinch rollers. These must be placed over the grit rollers. Also, if the number of middle pinch rollers installed
is greater than the number of grit rollers used, then detach the extra middle pinch rollers.
Remove when not using roll media.
If roll media is allowed to stand unused in a loaded state for an extended period, the media may sag. This can cause
poor printing quality and motor errors, so be sure to remove and store such media when not in use.
Media clamp
Cutting carriage
Pinch roller
Rightmost grit
pattern
23456
Middle pinch rollers
This indicates which pinch roller, counting from
the right as viewed from the front, is displaced.
(The right pinch roller is included in the count.)
The number displayed may be from the second
("2ND") to the sixth ("6TH"), depending on the
number used.
PINCHROLL ERROR
XXX FROM RIGHT
OK
Not OK
Pinch rollers
Either RIGHT or
LEFT is displayed.
PINCHROLL ERROR
INVALID *** POS
- For the USA 3
- For Canada 3
- Contents 4
- To Ensure Safe Use 7
- Warning Labels 13
- Avis sur les avertissements 14
- ATTENTION 14
- PRUDENCE 14
- À propos des symboles 14
- Printer Unit 21
- Ink Cartridges 22
- Chapter 1 24
- Introduction 24
- 1-1 Introduction 25
- 1-2 Part Names and Functions 26
- Chapter 1 Introduction 27
- Operation Panel 28
- Chapter 2 30
- Operation 30
- The Power-saving Feature 32
- Loading Media 33
- OK Not OK 34
- Chapter 2 Operation 35
- Close the front cover 37
- PINCHROLL ERROR 38
- XXX FROM RIGHT 38
- INVALID *** POS 38
- Cutting Off the Media 39
- General Guide for Adjustment 41
- 2-4 Starting Output 42
- Printing Tests and Cleaning 43
- 2-5 If Ink Runs Out 44
- If Ink Runs Out 45
- 2-6 Performing Cutting 46
- Performing a Cutting Test 47
- Chapter 2 Operation 48
- Chapter 3 50
- Maintenance and Adjustment 50
- Disposing of Discharged Ink 51
- Press a second time 52
- Cleaning 53
- Start cleaning 54
- How to Perform Cleaning 55
- Remove the side cover 56
- Replacing the Wipers 59
- Detach the old wipers 60
- Insert the new wipers 60
- Attach the hook 60
- Attach the side cover 61
- Replacing the Blade 62
- SETUP SHEET 63
- Replace the separating knife 64
- Keep Performing Maintenance 66
- Chapter 4 68
- Feature Reference 68
- Procedure 69
- Description 69
- Loading a Saved Preset 72
- Assigning a Name to a Preset 72
- Print a test pattern 74
- Enter the correction value 77
- Using Transparent Media 79
- Printing Hard-to-dry Media 79
- How to Load Sheet Media 83
- Deactivating the Sleep Mode 86
- 6. and fine-tune 94
- Default Setting 95
- Printing with Crop Marks 96
- Aligning Manually and Cutting 98
- Set the align points 99
- Chapter 4 Feature Reference 100
- 6. and fine-tune the 101
- Viewing the Network Settings 105
- Printing a System Report 106
- 4-12 Performing Maintenance 107
- 4-13 Menu List 109
- Language and Unit Menu 113
- Function Menu 114
- What to Do If 116
- Chapter 5 116
- Chapter 5 What to Do If 117
- Colors Are Unstable or Uneven 118
- 5-3 The Media Jams 120
- Media Wrinkles or Shrinks 121
- Media Feed Is Not Straight 121
- Media Feed Is Not Smooth 121
- What to Do First 122
- 5-6 If a Message Appears 123
- Chapter 6 128
- Specifications 128
- 6-1 Usable Media 129
- 6-2 Printing/Cutting Area 130
- Chapter 6 Specifications 131
- 6-3 About the Blade 132
- 6-5 Specifications 134
Related products and manuals for Print & Scan Roland VersaCamm VP-540i
Print & Scan Roland FJ-40 User Manual
(99 pages)
(99 pages)
Print & Scan Roland CJ-540 Specifications
(32 pages)
(32 pages)
Print & Scan Roland VS-540 User Manual
(2 pages)
(2 pages)
Print & Scan Roland RA-640 Setup Guide
(56 pages)
(56 pages)
Print & Scan Roland XC-540MT User Manual
(172 pages)
(172 pages)
Print & Scan Roland XR-640 Setup Guide
(60 pages)
(60 pages)
Print & Scan Roland COLORCHOICE User's Guide
(50 pages)
(50 pages)
Print & Scan Roland FJ-40 Specifications
(28 pages)
(28 pages)
Print & Scan Roland CJ-540 User Manual
(120 pages)
(120 pages)
Print & Scan Roland XC-540MT User Manual
(19 pages)
(19 pages)
Print & Scan Roland PC-12 User Manual
(49 pages)
(49 pages)
Print & Scan Roland VS-640i Setup Guide
(52 pages)
(52 pages)
Print & Scan Roland MPX-60 User Manual
(68 pages)
(68 pages)
Print & Scan Roland CX-300 User Manual
(102 pages)
(102 pages)
Print & Scan Roland VS-540 Setup Guide
(56 pages)
(56 pages)
Print & Scan Roland LEC-300A User Manual
(2 pages)
(2 pages)
Print & Scan Roland RA-640 Specifications
(50 pages)
(50 pages)
© 2020, manymanuals.com. All rights reserved. | 2.776 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals