Roland SC-7 User Manual Page 121

  • Download
  • Add to my manuals
  • Print
  • Page
    / 135
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 120
119
Chapter 7: What to Do If...
7-2 What to Do If an Error Message Appears
Meaning
An operation command was given while the
cover or front cover is open.
The print head was returned to its standby
position to be capped, canceling current printing
job.
Because emergency stop was effected more than
10 min.
Only a small amount of ink remains.
* The message at left indicates that there is little
remaining ink in the No. 1 and No. 7 ink-
cartridge ports.
An ink cartridge was removed.
A request to insert an ink cartridge was made
from this machine.
A request to remove an ink cartridge was made
from this machine.
A request to insert a cleaning cartridge was made
from this machine.
A request to remove a cleaning cartridge was
made from this machine.
• The [SETUP] key was pressed even though no
media is loaded.
Setup was performed with no media at the
correct location.
An attempt was made to load media that is too
small.
• [EDGE SENSE] is set to [ENABLE], but
transparent media was loaded.
Printing test was attempted with no media
loaded.
The [SETUP] key was pressed with the pinch
rollers up.
The pinch rollers were raised during setup.
A problem was found in the data received.
The head height and the loaded media do not
match.
Action
Close the cover or front cover.
Turn power off by pressing [POWER] key to
reset.
Interrupted printing is not resumed. Repeat
printing from the beginning.
Replace the empty ink cartridge.
Insert the specified ink cartridge.
Take out the specified ink cartridge.
Insert the specified cleaning cartridge.
Take out the specified cleaning cartridge.
• Load media at the correct location and press the
[SETUP] key again (see "2-3 Loading Media").
Replace with media of loadable size.
Wipe off the grime on the reflective tape, then
perform setup again.
• Replace with media of loadable size.
• When using transparent media, set [EDGE
SENSE] to [DISABLE] (see "6-2 Description of
Menus").
Load the media and try again.
Press the [ENTER] key to continue.
Move the loading lever all the way to "LOAD" to
lower the pinch rollers, then press the [SETUP]
key (see "2-3 Loading Media").
Make sure the cable is attached securely.
Change the head height to the specified height
and press the [ENTER] key.
Messages
CLOSE THE COVER
AVOIDING DRY-UP
TURN OFF POWER
1
_
2
3
4
5
6
7
_
8
9
10
11 12
SET SOL CRT.
1 2 3 4 5 6 7 8 9 10 11 12
REMOVE SOL CRT.
1 2 3 4 5 6 7 8 9 10 11 12
SET SOL CL-LIQUID
1 2 3 4 5 6 7 8 9 10 11 12
REMOVE SOL CL
1 2 3 4 5 6 7 8 9 10 11 12
SHEET SET ERROR
SET AGAIN
SHEET NOT LOADED
PRESS SETUP KEY
PINCHROLL ERROR
LOWER PINCHROLL
DATA ERROR
CANCELING...
SET HEAD HEIGHT
TO ***
* [1 2 3 4 5 6 7 8 9 10 11 12] indicate the numbers of the ink-cartridge ports. The character indicating the number of the ink-
cartridge port flashes when action is necessary.
[Example]
If "4,5,10,11" is flashing:
Install ink cartridges in ink-cartridge ports 4, 5, 10, and 11.
SET SOL CRT.
123456789101112
Downloaded From ManualsPrinter.com Manuals
Page view 120
1 2 ... 116 117 118 119 120 121 122 123 124 125 126 ... 134 135

Comments to this Manuals

No comments