Roland SC-7 User Manual Page 88
- Page / 135
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
86
Chapter 5: Maintenance
5-2 Cleaning Using the Cleaning Kit
Cleaning using the cleaning kit should be carried out when automatic cleaning and forced cleaning from the [HEAD
CLEANING] menu fail to correct image drop-out. Remove any ink buildup of dust or grime around the print heads,
which can cause image drop-out or ink drips. We also recommend performing periodic cleaning using the cleaning kit to
prevent problems like these during printing.
If image drop-out persists even after performing cleaning with the cleaning kit, or if the cleaning kit is used up, contact
your authorized Roland DG Corp. dealer or Roland DG Corp. service center.
The heads are consumable parts. The useful life is six billion shots per nozzle.
Cleaning Using the Cleaning Kit
1
Switch on the main power switch on the back
of the machine.
Leave media unloaded at this time.
2
While holding down the [CLEANING] key,
switch on the [POWER] key.
3
Press the [ ] and [ ] keys to select [CLEAN-
ING].
4
Press the [ENTER] key.
The screen shown in the figure appears, and the print-
head carriage moves to the middle of the left cover.
5
Make sure the screen shown in the figure is
displayed, then remove the four screws and
open the left and right covers.
Before starting cleaning, read through this section carefully to familiarize yourself with the procedures, then carry out the
cleaning operations quickly and accurately.
Cleaning is performed while the caps on the print heads are detached, so cleaning must be completed before the heads dry out.
It is suggested that cleaning be completed in thirty minutes or less.
If it appears that cleaning operations may take more than thirty minutes, stop the cleaning operations and follow the steps below.
1. Attach the cover and tighten the screws.
2. Press the [ENTER] key. (Cleaning of the print heads starts.)
3. Again carry out cleaning using the cleaning kit.
MAINTENANCE
CLEANING
NOW PROCESSING. .
FINISHED
CLEANING?
Take care not to drop the covers when removing
them. If dropped, the impact may cause them to
break.
Screws
Cover
Downloaded From ManualsPrinter.com Manuals
- User’s Manual 1
- For the USA 2
- For Canada 2
- Contents 3
- Features of the SC-545EX 6
- To Ensure Safe Use 10
- À propos des symboles 11
- Avis sur les avertissements 11
- Chapter 1: 17
- Getting Started 17
- 1-1 Checking Accessories 18
- 1-2 Part Names 19
- Inside the Front Cover 20
- Operation Panel (1) 20
- Operation Panel (2) 21
- Installation Environment 22
- Step 1: Assemble the Stand 23
- Chapter 1: Getting Started 24
- 1-4 Connecting the Cables 29
- Connecting to the Computer 30
- Securing the Cable 31
- BK CY MG LC LM YE 32
- Filling Ink 33
- ENV. MATCH 34
- REPLACE KNIFE 35
- FINISHED ? 35
- 1-6 Installing the Blade 36
- Chapter 2: 39
- Basic Operation 39
- Switching On the Power 41
- Chapter 2: Basic Operation 42
- 2-3 Loading Media 43
- PINCHROLL ERROR 46
- INVALID LEFT POS 46
- SETUP SHEET 46
- ROLL 46
- PIECE 47
- Adjusting the Head Height 48
- Separating the Media 50
- Removing the Media 50
- 2-4 Printing 51
- 2-5 Cutting 53
- Test Cutting 54
- 2-6 Printing and Cutting 56
- Printing Area 57
- AUTO ALIGN 58
- BASE - ALIGN 58
- Aligning Manually 60
- Chapter 3: 61
- Using the Print Heater 61
- Switching On the Print Heater 62
- 3-2 Loading Media 63
- 3-3 Printing and Cutting 64
- Cutting/Printing and Cutting 65
- Chapter 4: 67
- A Wide Variety of 67
- Operations 67
- Replacing an Ink Cartridge 69
- 1＿ 2■ 3■ 4 ■ 5■ 6■ 70
- INK REMAINING 71
- Setting the Start Location 72
- To release the setting 73
- 4-4 Setting the Margins 74
- PRINTING ADJ 75
- TEST PRINT 75
- Bidirectional Correction 76
- Saving an Adjustment Value 77
- ADJUST BI-DIR 78
- PRESETTING 1 78
- NOW PROCESSING 79
- PRINT-CUT ADJ 79
- COMPLETED 79
- PRINT - CUT ADJ 80
- PRINT - CUT ADJ 81
- FEED SETTING 81
- To resume printing 82
- Stopping Printing or Cutting 82
- SET LENGTH 83
- 0.0 m 20.0 m 83
- PRESS THE POWER 84
- KEY TO CLEAN 84
- Chapter 5: 85
- Maintenance 85
- 5-1 Cleaning the Print heads 86
- HEAD CLEANING 87
- FINISHED 88
- CLEANING? 88
- NOW PROCESSING. 90
- 5-3 Replacing the Wiper 91
- 5-4 Other Cleaning Tasks 92
- 5-8 When Moving the Unit 96
- Chapter 6: 99
- Menus and Keys 99
- 6-1 Menus Flowchart 100
- 6-2 Description of Menus 106
- 6-3 Description of Keys 110
- Chapter 7: 113
- What to Do If 113
- W 1234 mm 114
- Top menu 114
- 7-1 What to Do If 115
- Media Wrinkles or Warps 117
- The Media Becomes Jammed 118
- Capping the Print heads 119
- SET SOL CRT 121
- Chapter 7: What to Do If 122
- Messages 122
- Chapter 8: 125
- Specifications 125
- 8-1 Media Conditions 126
- Acceptable Media Width 127
- Chapter 8: Specifications 129
- 8-4 About Blade Life 130
- 8-6 Specifications 132
- Use in an operating environ 133
- R2-041129 135
Related products and manuals for Recording Equipment Roland SC-7
Recording Equipment Roland R-8 mkII User Manual
(159 pages)
(159 pages)
Recording Equipment Roland S-760 User Manual
(19 pages)
(19 pages)
Recording Equipment Roland VS-840EX User Manual
(211 pages)
(211 pages)
Recording Equipment Roland CD-2u User Manual
(140 pages)
(140 pages)
Recording Equipment Roland XP-50 User Manual
(37 pages)
(37 pages)
Recording Equipment Roland BR-1200CD User Manual
(364 pages)
(364 pages)
Recording Equipment Roland D-110 User Manual
(299 pages)
(299 pages)
Recording Equipment Roland ME-8B User Manual
(25 pages)
(25 pages)
Recording Equipment Roland XP-50 User Manual
(181 pages)
(181 pages)
Recording Equipment Roland VC-1 D-50 User Manual
(154 pages)
(154 pages)
Recording Equipment Roland BR-8 User Manual
(127 pages)
(127 pages)
Recording Equipment Roland MC-4 Owner's Manual
(180 pages)
(180 pages)
(26 pages)
Recording Equipment Roland VP-70 User Manual
(84 pages)
(84 pages)
© 2020, manymanuals.com. All rights reserved. | 0.084 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals