Roland XP-60 Owner's Manual download pdf (Page 108)

108

Performing realtime recording

When you have completed preparatory steps correctly, it’s

time to realtime record.

❶ Make sure that the Play display (SEQ(Song)) is up.

❷ Move the cursor to the song number and select the

song you wish to record.

When recording a new song, select “00:InternalSong.” When

recording over a song saved on the disk, choose the number

of that song.

❸ Press [REC] to call up the Realtime Rec Stand-by dis-

play (SEQ).

The [REC] indicator will blink and the metronome will start

sounding.

✳ If you have selected a song saved on disk, a window

will ask “This Song is not Internal Song. Load any-

way?” If you want to erase the song from the internal

memory and load the new song, press [F5] (OK). If you

decide not to erase the song from the internal memory,

press [F6] (Cancel).

✳ To turn off the metronome, set the Mode parameter

(SEQ/Setup/SEQ System Setup) OFF.

✳ To interrupt recording, press [REC] or [EXIT] to return

to the Play display (SEQ(Song)).

❹ Move the cursor to “M” and set the recording start

measure.

❺ Move the cursor to “ ” and set the tempo.

❻ If you want to use loop recording, move the cursor to

“Loop” and make settings for the loop recording. If

not, set it OFF.

❼ Move the cursor to “Mode” and select the recording

mode.

❽ Move the cursor to “Qntz” and select quantization

type. If you don’t want to quantize when recording, set

it OFF.

When applying quantization to recording, press [F4]

(Quantize) to open the Recording Quantize window and

make Quantize settings. After you have completed your set-

tings, press [EXIT] or [F4] (Quantize) to close the Recording

Quantize window.

❾ Move the cursor to “Count In” and specify the record-

ing start method.

❿ Select the recording destination. When recording on a

Phrase track, use TRACK/PART [1]–[16]. When

recording in a Pattern, press [PATTERN] and specify

the Pattern number.

The button indicator of the selected recording destination

Phrase track or Pattern will blink. The button indicators of

the Phrase tracks containing sequencer data stay lighted.

If you wish to record using a Part of a number differ-

ent from the Phrase track’s, or recording in a Pattern,

select the Part used for recording. Move the cursor to

“PART,” and either turn the VALUE dial or press

[INC]/[DEC] to choose the Part.

✳ When the cursor is at “PART,” pressing TRACK/

PART [1]–[16] will also select the correspondingly

numbered Phrase track.

When changing the Patch or Rhythm Set, move the

cursor to the group or number and select a different

Patch/Rhythm Set.

If you want to change the Performance, press [PERFORM] to

call up the Play display (PERFORM) and select another

Performance. To return to the Realtime Rec Stand-by display

(SEQ), press [SEQUENCER].

✳ If you select another Patch, Rhythm Set or Performance

on the Realtime Rec Stand-by display (SEQ), the Bank

Select number and Program number of that

Patch/Rhythm Set/Performance will automatically be

recorded at the recording start position. However, if

the Performance Ctrl-Ch parameter (SYSTEM/MIDI

Param) has the same setting as the MIDI channel of the

specified Part (when the Patch assigned to a Part of a

Performance has been selected), be aware that this will

actually select a different Performance.

Begin recording using the recording method selected

by “Count In.” When recording begins, the [REC] indi-

cator will light. The BEAT indicator will also blink in

red for the first beat and in green for other beats.

✳ When recording begins, the Phrase tracks with lighted

indicators will play back. If you don’t want some

Phrase tracks to play back during recording, move the

cursor to a position other than “TRK” or “PART,” and

press TRACK/PART [1]–[16] to turn off the indicators

of unwanted Phrase tracks.

When you finish recording, press [STOP/PLAY].

...........................................................................................................

You can specify Punch points (area auto punch-in recording

is to take place) if you’re going to use this function.

❶ Make sure that the Mode parameter is set to

A.PUNCH on the Realtime Rec Stand-by display

(SEQ).

❷ Press [F6] (A.Punch) to open the Punch Point window.

❸ Move the cursor to “In” and set the recording start

position.

When you are using a Locate position to specify recording

start position, press [LOCATE] to light the indicator and

specify the Locate position number.

❹ Move the cursor to “Out” and set the recording end

position.

If you are setting the recording start position using a Locate

position, set the Locate position number for the recording

end position in the same way.

✳ The recording end position that is set for “Out” will

not be included in the recording area.

✳ A recording area setting of less than one beat is

invalid.

❺ After you complete settings, press [EXIT] or [F6]

(A.Punch) to close the Punch Point window.

Chapter 4. Playing back and recording a song

1 2 ... 103 104 105 106 107 108 109 110 111 112 113 ... 247 248

Roland XP-60 Owner's Manual Page 108

Comments to this Manuals

Roland XP-60 Owner's Manual Page 108

Comments to this Manuals

Related products and manuals for Musical Instruments Roland XP-60