Roland XP-60 Owner's Manual download pdf (Page 162)

162

Source

Specifies the data to be transmitted through combinations as

shown below.

For instance, if you wish to transmit the settings of the cur-

rent Performance and the Patch or Rhythm Set assigned for

each Part, specify “PERFORM TEMP:+PATCH.”

1: All Patches, Performances and Rhythm Sets in USER

group

2: The current Performance, Patch and Rhythm Set

3: The Performance of the specified number in USER group

4: The current Performance

5: The current Performance and the Patch or Rhythm Set

assigned to each Part of the Performance

6: The current Performance’s Bank Select and Program num-

bers, as well as Volume and Pan messages of Parts with the

Rx switch ON. Use this selection when you want to make a

rough recording of Performance settings balance. Since data

is transmitted as controller numbers, the data amount will

stay relatively small.

7: The Patch of the specified number in USER group

8: The current Patch

9: The Rhythm Set of the specified number in USER group

10: The current Rhythm Set

11: System

✳ Number 6 cannot be selected from Patch mode. In

addition, Volume and Pan messages to be transmitted

are not part of the selected Performance data; they are

global settings for the entire XP-80 instead. To check

the data, use the Part Information display (PER-

FORM/Info).

Destination

“to Seq” means that data will be transmitted to the internal

song.

Here you can also specify the Phrase track or Pattern to

which the data will be sent, and the Song position (measure-

beat-clock) in that track or Pattern. Phrase tracks or Patterns

containing no sequencer data cannot be selected.

❶ Make sure that the Utility Menu (UTILITY) is up.

❷ Press [F6] (Menu) to select Menu 1, then press [F4]

(Xfer) to select Data Transfer.

You can also select Data Transfer by moving the cursor to “4

Data Transfer” and pressing [ENTER] on the Utility Menu

display (UTILITY), or pressing the numeric key [4], then

[ENTER].

❸ Press [F2] (to Seq) to call up the Data Transfer to Seq

display (UTILITY/Xfer).

❹ Move the cursor to “Source” and specify the data you

want to transmit.

❺ Press [d] to move the cursor and select the Phrase

track or Pattern to which you want to transmit data.

You can also select a Phrase track by pressing TRACK/

PART [1]]–[16].

To select a Pattern, press [PATTERN] and specify the Pattern

number.

❻ Press [r ] to move the cursor and specify the Song

position in the selected track or Pattern to which data

will be transmitted.

❼ Press [F6] (Execute) to transmit the data.

While data is being transmitted, the display will read

“Transmitting...”

✳ To interrupt data transmission, press [EXIT].

Transmitting data to user memory

You can transmit Patch, Performance or Rhythm Set settings

to the user memory and System settings to the system mem-

ory. By loading sound data from disk or Expansion Boards

to user memory, you can add many different sounds to your

performance.

✳ If you wish to transmit an entire data file, use the Load

function (Disk/Load).

Source

Specifies the data to be transmitted through combinations as

shown below.

For instance, if you want to transmit Rhythm Set 001 of the

Expansion Board inserted into the XP-80’s EXP-A slot, speci-

fy “RHYTHM XP-A:001-001.”

Source

ALL

USER 1

TEMP 2

USER 01-32 3

PERFORM TEMP

-PATCH 4

+PATCH 5

CTRL 6

PATCH

USER 001-128 7

TEMP 8

RHYTHM

USER 001-002 9

TEMP 10

SYSTEM User 11

Chapter 8. XP-80 memory settings (Utility mode)

[UTILITY]➞[4]➞[ENTER]

1 2 ... 157 158 159 160 161 162 163 164 165 166 167 ... 247 248

Comments to this Manuals

No comments

Roland XP-60 Owner's Manual Page 162

Comments to this Manuals

Related products and manuals for Musical Instruments Roland XP-60