Roland XP-60 Owner's Manual Page 57
- Page / 248
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Modulating sounds–Adding Vibrato,
Tremolo, etc.
Using controllers to change how sounds
are played (LFO&Ctl)
LFO1 Prm (LFO 1 parameter) display/LFO2 Prm
(LFO2 parameter) display
An LFO (Low Frequency Oscillator) causes change over a
cycle in a sound. Each Tone has two LFOs, and these can be
used to cyclically change the pitch, cutoff frequency and vol-
ume to create modulation-type effects such as vibrato, wah-
wah and tremolo. Both LFOs have the same parameters so
only one explanation is needed.
Waveform (LFO waveform)
Selects the waveform of the LFO. The selected waveform is
graphically displayed.
TRI: Triangle wave
SIN: Sine wave
SAW: Sawtooth wave
SQR: Square wave
TRP: Trapezoidal wave
S&H: Sample and hold wave
RND: Random wave
CHS: Chaos wave
Key Sync (LFO key sync)
Specifies whether you want the LFO cycle to start in sync
with the timing of a key press (ON) or not (OFF).
Rate (LFO rate)
Adjusts the modulation rate of the LFO waveform.
✳ If you have selected CHS (chaos waveform) for
Waveform parameter, the Rate parameter setting has
no effect.
✳ If you have set the Ext Sync parameter to CLK, this
parameter will indicate a note value in multiples of a
quarter note. The corresponding note value symbol is
also displayed. This allows you to set the Rate parame-
ter in terms of a note length in the sync tempo.
Ext Sync (LFO external sync)
Selects how the LFO is to be synchronized.
OFF: Unsynchronized.
CLK: Synchronizes the LFO delay time to the Patch Tempo
parameter setting (PATCH/Common/Common General) or
Perform Tempo parameter setting (PERFORM/Common/
Common) or sequencer’s tempo clock.
If you want to use a fixed tempo in Patch mode, set the
Clock Source parameter (PATCH/Common/Common
General) to PATCH and set the desired tempo.
If you want to use the sequencer tempo clock in Patch mode,
set the Clock Source parameter (PATCH/Common/
Common General) to SEQUENCER.
If you want to use a fixed tempo in Performance mode
(Perform Tempo parameter setting), set the Clock Source
parameter (PERFORM/Common/Common) to PERFORM
and set the desired tempo.
If you want to use the sequencer tempo clock in Performance
mode, set the Clock Source parameter (PERFORM/
Common/Common) to SEQUENCER.
Fade Mode (LFO fade mode)
Selects how the LFO is to be applied.
ON-IN: The LFO will fade in after the key is pressed.
ON-OUT: LFO is applied immediately on key press then
fades out.
OFF-IN: LFO will fade in after key release.
OFF-OUT: LFO is applied immediately when the key is
pressed and will begin to fade out at key release.
key is
pressed
high (more)
low (less)
WG Pitch /
TVF Cutoff Frequency /
TVA Level / TVA Pan
Delay
Time
Fade
Time
Depth
key is
pressed
high (more)
low (less)
WG Pitch /
TVF Cutoff Frequency /
TVA Level / TVA Pan
Delay Time Fade Time
Depth
high (more)
low (less)
WG Pitch /
TVF Cutoff Frequency /
TVA Level / TVA Pan
Delay
Time
Fade
Time
Depth
key is
pressed
key is
released
key is
pressed
high (more)
low (less)
WG Pitch /
TVF Cutoff Frequency /
TVA Level / TVA Pan
Delay
Time
Fade
Time
Depth
key is
released
57
Chapter 3. Creating your own sounds
[PATCH]➞[F5] (LFO&Ctl)➞[F1] (LFO1)/[F2] (LFO2)
- OWNER’S MANUAL 1
- IMPORTANT SAFETY INSTRUCTIONS 2
- SAVE THESE INSTRUCTIONS 2
- IMPORTANT NOTES 4
- Protect tab 5
- Write (writing permitted) 5
- Protect (writing prohibited) 5
- Features of the XP-60/XP-80 6
- Chapter outlines 7
- Contents 8
- Front panel 14
- I. SEQUENCER section 15
- Side panel 16
- Rear panel 17
- XP-80 configuration 18
- Performances 19
- Rhythm Sets 19
- Basic operation 20
- VALUE dial 23
- [INC] and [DEC] 23
- [0]–[9] (Numeric Keys) 23
- Chapter 2. Playing 26
- Changing sound characters 28
- Playing in Performance mode 29
- (Sound Palette) 32
- Playing in Rhythm Set mode 33
- Rhythm Set 34
- Playing an arpeggio 35
- Recording an arpeggio 37
- (Octave Shift) 37
- Regarding effects 39
- Sound editing procedures 40
- Note on Tone editing 42
- Editing a Performance 43
- Part number 44
- MIDI channel 44
- Keeping edited sound 45
- Functions of Patch parameters 46
- Common Control display 47
- Structure display 49
- Pitch display 52
- Pitch Envelope display 53
- TVF Envelope display 54
- Time 1 Time 2 Time 3 Time 4 56
- (LFO2 parameter) display 57
- Ext Sync (LFO external sync) 57
- Control Switch display 59
- EFX Type name 60
- Chorus display 64
- Reverb display 64
- Settings common to the entire 65
- Performance (Common) 65
- [PERFORM]➞[F1] (Common) 65
- Lower Upper 66
- Key range specified for Patch 66
- [PERFORM]➞[F4] (MIDI) 67
- [PERFORM]➞[F5] (Effects) 68
- [PERFORM]➞[F6] (Info) 69
- Naming a Rhythm Set (Common) 70
- Rhythm Tone (Key WG) 70
- [RHYTHM]➞[F3] (Key TVF) 71
- TVA Envelope display 72
- Bend Range (Pitch bend range) 72
- Mute Group 72
- [RHYTHM]➞[F5] (Key Ctl) 73
- 2: OVERDRIVE 74
- 3: DISTORTION 74
- 4: PHASER 75
- 5: SPECTRUM 75
- 6: ENHANCER 75
- 7: AUTO-WAH 76
- 8: ROTARY 76
- 9: COMPRESSOR 76
- 10: LIMITER 77
- 11: HEXA-CHORUS 77
- 12: TREMOLO-CHORUS 77
- 13: SPACE-D 78
- 14: STEREO-CHORUS 78
- 15: STEREO-FLANGER 78
- 16: STEP-FLANGER 79
- 17: STEREO-DELAY 79
- 18: MODULATION-DELAY 80
- 19: TRIPLE-TAP-DELAY 80
- 20: QUADRUPLE-TAP-DELAY 81
- 21: TIME-CONTROL-DELAY 82
- 22: 2VOICE-PITCH-SHIFTER 82
- 24: REVERB 83
- 25: GATE-REVERB 84
- 26: OVERDRIVE ➞ CHORUS 84
- 27: OVERDRIVE ➞ FLANGER 84
- 28: OVERDRIVE ➞ DELAY 85
- 29: DISTORTION ➞ CHORUS 85
- 30: DISTORTION ➞ FLANGER 85
- 31: DISTORTION ➞ DELAY 85
- 32: ENHANCER ➞ CHORUS 85
- 33: ENHANCER ➞ FLANGER 86
- 34: ENHANCER ➞ DELAY 86
- 35: CHORUS ➞ DELAY 86
- 36: FLANGER ➞ DELAY 87
- 37: CHORUS ➞ FLANGER 87
- [SYSTEM]➞[F1] (Setup) 88
- Adjusting tuning (Tune) 89
- [SYSTEM]➞[F2] (Tune) 89
- MIDI settings (MIDI) 90
- [SYSTEM]➞[F3] (MIDI) 90
- [SYSTEM]➞[F4] (Control) 92
- Arpeggio settings (Arpeg) 93
- [SYSTEM]➞[F5] (Arpeg) 93
- [SYSTEM]➞[F6] (Info) 95
- About the sequencer 96
- Playing back a song 97
- (Quick Play) 98
- Reserve 1 99
- Reserve 2 99
- Reserve 3 99
- Playing back a Pattern 101
- Before you start to record 104
- Selecting instrument sounds 105
- Setting the time signature 105
- Performing realtime recording 108
- (Realtime Erase) 110
- Recording tempo changes 110
- Canceling recording (Undo) 112
- Inputting data step by step 113
- (Step recording) 113
- Inputting chords 114
- Inputting ties 114
- Inputting a dotted note 114
- Inputting rests 114
- Erasing wrong notes 114
- Deleting recording (Undo) 115
- Saving only a song 116
- Chapter 5. Editing a song 117
- Settings for an entire song 118
- Locate function 119
- Setting loop 120
- [SEQUENCER]➞[F5] (Loop) 120
- About Track Edit 121
- [SEQUENCER]➞[F3] (TrkEdit) 121
- Setting the editing area 122
- Copying a phrase – 3 Copy 124
- (Insert measure) 126
- (Change velocity) 127
- (Change MIDI channel) 128
- (Change gate time) 129
- Aligning a song’s timing 136
- (Quantize) 136
- Grid quantize 137
- Shuffle quantize 138
- Groove quantize 139
- Phrase track/Pattern 146
- [SEQUENCER]➞[F4] (Micro) 146
- Erasing sequencer data 149
- Moving sequencer data 149
- Copying sequencer data 149
- Getting ready to use RPS 150
- Playing using RPS 151
- Getting ready for Chain Play 153
- Saving a chain to disk 154
- Chain play 154
- About Utility mode 155
- Performance write 156
- Patch write 156
- Rhythm Set write 156
- [UTILITY]➞[1]➞[ENTER] 156
- Performance copy 157
- [UTILITY]➞[2]➞[ENTER] 157
- Patch copy 158
- Rhythm Set copy 159
- – 3 Initialize 160
- 4 Data Transfer 161
- [UTILITY]➞[4]➞[ENTER] 162
- [UTILITY]➞[5]/[6]/[7]➞[ENTER] 164
- – 8 Factory (Factory preset) 165
- About Disk mode 166
- XP-80 – 1 Load 167
- Saving data to disk – 2 Save 168
- Formatting the disk for the 169
- XP-60/XP-80 – 3 Format 169
- 5 Verify 170
- Changing the name of disk – 170
- Deleting unwanted files – 171
- 7 Delete (Delete file) 171
- Renaming a file – 8 Rename 171
- 9 Info (Disk information) 172
- Entering GM mode 173
- Modifying GM mode settings 174
- [SHIFT]+[PERFORM]➞[F6] (Info) 175
- (GM Utility) 176
- Transfer (GM Data Transfer) 177
- Techniques for using Patches 178
- Using the XP-80 to play live 179
- Song making techniques 180
- Changing the Patch 181
- Changing the Performance 181
- Changing the Rhythm Set 181
- Using external MIDI devices 182
- Synchronization with external 183
- MIDI devices 183
- Disk Recorder 184
- Playing back Song files 185
- Recording on the VS-880 185
- MIDI OUT 186
- MIDI OUTMIDI IN 186
- Troubleshooting 187
- Error messages 188
- Parameter List 190
- WG Group 191
- TVF Group 191
- TVA Group 192
- LFO&Ctl Group 192
- Effects Group 193
- Performance Parameters 194
- Rhythm Set Parameters 195
- Key TVF Group 196
- Key TVA Group 196
- Key Ctl Group 196
- GM Parameters 197
- Info Group 198
- EFX Parameters 199
- 39: FLANGER/DELAY (P.88) 203
- 40: CHORUS/FLANGER (P.88) 203
- System Parameters 204
- Control Group 205
- Arpeg Group 205
- Factory Preset Settings 206
- INT-B (Internal B) 207
- Patch List 208
- GM (GM Group) 210
- Rhythm set List 211
- Performance List 212
- Arpeggio style list 213
- MIDI implementation 214
- ■ Channel Mode messages 216
- ■ System Realtime messages 217
- ■ System Exclusive messages 217
- ■ Channel Voice messages 218
- ■ Channel voice messages 219
- 1-1-1.System Common 222
- 1-1-2.Scale Tune 222
- 1-2.Performance 222
- 1-2-1.Performance Common 223
- 1-2-2.Performance Part 223
- 1-3.Patch 223
- 1-3-1.Patch Common 223
- 1-3-2.Patch Tone 224
- 1-4.Rhythm Setup 225
- 1-4-1.Rhythm Common 225
- 1-4-2.Rhythm Note 225
- ■ Address block map 226
- 2.GS (Model ID = 42H) 226
- 2-1.Scale Tune 226
- 6. Supplementary material 226
- Thus, the address is: 227
- 00 00H Patch Common 228
- MIDI Implementation Chart 229
- Specifications 231
- Quick reference of displays 232
- Performance mode [PERFORM] 233
- Rhythm Set mode [RHYTHM] 234
- GM mode [SHIFT] + [PERFORM] 235
- Sequencer mode [SEQUENCER] 236
- Chain Play mode [CHAIN PLAY] 238
- System mode [SYSTEM] 238
- Utility mode [UTILITY] 239
- Disk mode [DISK] 240
- Information 246
Related products and manuals for Musical Instruments Roland XP-60
Musical Instruments Roland RP101 User Manual
(52 pages)
(52 pages)
Musical Instruments Roland RS-70 User Manual
(178 pages)
(178 pages)
Musical Instruments Roland RP201 User Manual
(60 pages)
(60 pages)
Musical Instruments Roland HP 557R User Manual
(140 pages)
(140 pages)
(11 pages)
Musical Instruments Roland FP-3 User Manual
(64 pages)
(64 pages)
© 2020, manymanuals.com. All rights reserved. | 0.306 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals