Roland XP-60 Owner's Manual download pdf (Page 127)

❶ Make sure that the Track Edit Menu display

(SEQ/TrkEdit) is up.

❷ Press [F6] (Menu) to select Menu 1, then press [F5]

(Trans) to call up the Transpose display (SEQ/

TrkEdit).

This display can also be called up by moving the cursor to “5

Transpose” and pressing [ENTER] on the Track Edit Menu

display (SEQ/TrkEdit). Or press the numeric key [5], then

[ENTER].

❸ Move the cursor to Target track and select the Phrase

track(s) or Pattern from which you want to transpose.

❹ When assigning the editing area by measures, move

the cursor to “Measure” and specify the measure num-

ber at which transpose is to start, then move the cursor

to “for” to specify the measure length to be transposed.

When using Locate positions, press [LOCATE], and move

the cursor to “From” to select the Locate number where you

want transposition to begin. Then move the cursor to “to”

and select the Locate number at which you want to end

transposition.

❺ Move the cursor to “Note Range” and set the range of

notes to be transposed.

You can also set this parameter through key input on the

keyboard.

❻ Move the cursor to “Bias” and set the transpose

amount.

❼ Move the cursor to “Channel” and select the MIDI

channel(s) of notes to be transposed.

If you have selected ALL, move the cursor to “Channel for

exclude” and select a single MIDI channel that will not be

transposed.

❽ Press [F6] (Execute) to initiate transposition.

...........................................................................................................

If your bass is played 1 octave higher than the staff notation,

use the Transpose function to lower it 1 octave.

To lower bass by 1 octave, set the Note Range parameter to

“lowest note-highest note” of the bass staff notation, and set

the Bias parameter to “-12.”

You can also use the Transpose function to change percus-

sion sounds. Suppose you want to change conga to tom. If

conga is assigned to note D4 note and tom to note C3, set the

Note Range parameter to “D4-D4”. To set the Bias parame-

ter, move the cursor to “Bias,” and press C3 key to specify “-

14 (C3).”

✳ Only when the Note Range parameter is set in the

form of a single note will the note name appear in

parentheses ( ) next the Bias parameter for reference.

...........................................................................................................

Modifying velocity – 6 Chg Velocity

(Change velocity)

This function modifies the keyboard playing dynamics

(velocity) of a specified note area.

Target track

Selects the Phrase track(s) or Pattern whose velocity you

want to modify.

TRK ALL: Phrase tracks 1–16

TRK 1–TRK 16: The specified Phrase track

PTN 001–PTN 100: The specified Pattern

Measure (From), for (to) (Editing area)

Specifies the area of measures over which velocity will be

modified.

Bias

Use this parameter to add a fixed bias amount to all veloci-

ties. A setting of +10 will increase all velocities by 10.

Magnify

Set this parameter if increases or decreases in velocity varia-

tions are desired. For less velocity variation, use settings of

99% or less. For more velocity variation, set it to 101% or

greater. With a setting of 100%, velocity values do not

change.

Channel (MIDI channel)

Specifies the MIDI channel(s) of notes for which velocity will

be modified.

To modify velocity for all notes, set this parameter to ALL.

When modifying the velocity for only the notes of a specific

MIDI channel, select that MIDI channel using this parame-

ter.

Note Range

Specifies the range of note numbers for which velocity will

be modified. For instance, to modify velocity for C3 to C4

note range, set this parameter to “C3–C4.”

Target track

127

Chapter 5. Editing a song

[SEQUENCER]➞[F3] (TrkEdit)➞[6]➞[ENTER]

1 2 ... 122 123 124 125 126 127 128 129 130 131 132 ... 247 248

Comments to this Manuals

No comments

Roland XP-60 Owner's Manual Page 127

Comments to this Manuals

Related products and manuals for Musical Instruments Roland XP-60