Roland SJ-600 User Manual Page 64
- Page / 77
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
62
Description of Menu Items
Description of Menus
Pressing the [MENU] key enters the menu mode.
Description of Menu Items
Default
value
Setting
range
FunctionSubmenu
Top
menu
SHEET
TYPE
— OPAQUE
CLEAR
OPAQUEThis is used to select either transparent or opaque material.
Select [OPAQUE] when the material loaded on the unit is not transpar-
ent. When using transparent material or when the printing area cannot
be detected, select [CLEAR].
For more information, see "What to Do If... -- [INVALID SHEET]
appears and the material cannot be detected even when the [SETUP]
key is pressed."
PRINT
AREA
MOVE TO
R-EDGE
SET R-EDGE
MOVE TO
L-EDGE
SET L-EDGE
EXIT
——
* This appears only when the material is in a loaded state.
This sets the printing area in the left-right direction (the direction of
carriage movement) of the loaded material.
With transparent material, automatic detection of the material width is
not performed. In such cases, use the [PRINT AREA] menu to specify
the printing area in the left-right direction. Even when using opaque
material, this can be used to specify a specific area for performing
printing.
Pressing the [ENTER] key while [MOVE TO R-EDGE] or [MOVE TO
L-EDGE] is displayed moves the carriage to the currently set right- or
left-hand edge of the material.
When setting a new printing area, make the setting with [SET R-
EDGE] or [SET L-EDGE].
For more information, see "User's Reference -- Printing at the Desired
Location -- Specifying a location in the left-right direction (the
direction of carriage movement)."
Press [EXIT] to quit this menu.
HEAD
CLEANING
TEST
PRINT
NORMAL
POWERFUL
——Before starting to print, you can carry out a printing test to check the
printing quality.
If the printing test shows a problem, clean the printing head.
Because cleaning subjects the head to wear and consumes ink, it should
only be performed when absolutely necessary. Performing cleaning
from the [POWERFUL] menu in particular subjects the head to early
wear and used up large amounts of ink.
[TEST PRINT]: Performs a printing test within an area of approxi-
mately 108 mm (4-5/16 in.) by 18 mm (6/8 in.). If a problem is found,
then continue by carrying out cleaning.
[NORMAL]: Performs cleaning of the printing heads. After cleaning,
carry out a printing test to make sure there are no problems with
printing quality.
You should usually choose [NORMAL]. ([CLEANING] does the
same thing as [HEAD CLEANING] - [START] displayed when the
[CLEANING] key is pressed.)
[POWERFUL]: Used when performing cleaning with [NORMAL]
several times does not restore the printing quality. After cleaning,
carry out a printing test to make sure there are no problems with
printing quality.
For more information, see "Setup for Printing -- 2 Test Printing" and
"Maintenance -- Cleaning the Printing Heads."
- SJ-600/500 1
- For the USA 2
- For Canada 2
- Contents 3
- To Ensure Safe Use 4
- Ink cartridge 8
- Avis sur les avertissements 10
- À propos des symboles 10
- Utiliser l'alimentation 15
- 1 Checking Accessories 16
- 3 Setting Up and Connection 20
- Connection 21
- 4 Installing Ink Cartridges 22
- [ K C M c m Y ] 23
- Ink cartridge ports 24
- Part Names 25
- Inside the Front Cover 26
- Rear View 26
- Operation Panel 27
- Five Modes 28
- Setup for Printing 29
- 1 Loading the Material 30
- W 1234 mm 31
- NORMAL BI-DIR 31
- Loading Sheet Material 32
- Installing the Media Clamps 33
- 2 Test Printing 34
- Printing Mode 35
- Printing Direction 35
- Stopping Printing Operations 36
- Pausing Printing Operations 36
- About the [EMPTY MODE] 37
- Remove the Material 38
- AUTO SHEET CUT 39
- DISABLE ENABLE 39
- When Operations Are Finished 40
- Maintenance 41
- Check How Much Ink Remains 43
- Cleaning the Printing Heads 44
- Disposal of Discharged Ink 45
- The POWER LED goes out 46
- Positioning groove 46
- When Moving the Unit 49
- User's Reference 51
- PRINT AREA 53
- SET R-EDGE 53
- Feed Correction 55
- -15 to +15 (In steps of 1) 56
- BIDIRECTION 56
- OVER PRINT 57
- 0 to 100 mm 58
- (In steps of 10 mm) 58
- PAGE MARGIN 58
- 20mm 10mm 58
- Height of the printing head 59
- Materials 60
- About the Printing Area 61
- Description of Keys 62
- Description of Menu Items 64
- Display Menus Flowchart 67
- OPAQUE/CLEAR 68
- NONE/ 2 / 3 68
- NONE, 15 to 120 min 68
- (In steps of 15 min) 68
- ENABLE/DISABLE 68
- What to Do If 70
- SHEET TYPE 71
- OPAQUE CLEAR 71
- The material becomes jammed 73
- Printed lines are misaligned 73
- Error Messages 74
- Specifications 75
- Interface Specifications 76
- R1-020320 77
Related products and manuals for Print & Scan Roland SJ-600
Print & Scan Roland SJ-745EX User Manual
(4 pages)
(4 pages)
Print & Scan Roland CJ-540 User Manual
(124 pages)
(124 pages)
Print & Scan Roland FJ-400 User Manual
(2 pages)
(2 pages)
© 2020, manymanuals.com. All rights reserved. | 0.792 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals