Roland HPD-15 User Manual Page 101
- Page / 116
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
101
MIDI Implementation
Appendices
❍Data set 1 DT1 (12H)
This is the message that actually performs data transmission, and is used when you wish to
transmit the data.
Status Data byte Status
F0H 41H, dev, 00H, 2EH, 12H, aaH, bbH, F7H
ccH, ddH, eeH,... ffH, sum
Byte Explanation
F0H Exclusive status
41H ID number (Roland)
dev Device ID (dev: 00H - 1FH (1 - 32) Initial value is 10H (17))
00H 2EH Model ID (HPD-15)
12H Command ID (DT1)
aaH
Address MSB: upper byte of the starting address of the transmitted
data
bbH Address 2nd : 2nd byte of the starting address of the transmitted data
ccH Address 3rd: 3rd byte of the starting address of the transmitted data
ddH
Address LSB: lower byte of the starting address of the transmitted data
eeH Data: The actual data to be transmitted. Multiple bytes of data are
transmitted in order starting from the address.
::
ffH Data
sum Checksum
F7H EOX (End Of Exclusive)
* The amount of data that can be transmitted at once time will depend on the type of data,
and data must be requested using a specific starting address and size. Refer to the
Address and Size listed in "Parameter Dump Request" (p. 108).
* If "Data Set 1" is transmitted successively, there must be an interval of at least 40ms.
* Regarding the checksum please refer to p. 109.
2. Transmit data
* When [SYSTEM]-(MIDI) Soft Thru is set to "ON", messages received in addition to the
following messages are also sent.
■Channel Voice Messages
* The following channel voice messages are transmitted on the channel specified as the
[SYSTEM]-(MIDI).
●Note off
Status 2nd byte 3rd byte
8nH kkH vvH
9nH kkH 00H
n = MIDI channel number: 0H - FH (ch.1 - ch.16)
kk = note number: 00H - 7FH (0 - 127)
vv = note off velocity: 00H - 7FH (0 - 127)
* With the Trigger Mode is set to "Shot", 9n kk 00H is transmitted afetr the set time has
elapsed.
* With the Trigger Mode is set to "Gate", 8n kk vvH is transmitted when you release the
pad.
* With the Trigger Mode is set to "Trig", Note On and 8n kk vvH are alternately
transmitted when you strike the pad.
* On the channel assigned to the pad part and the percussion parts, the note numbers
specified by the patch will be transmitted.
●Note on
Status 2nd byte 3rd byte
9nH kkH vvH
n = MIDI channel number: 0H - FH (ch.1 - ch.16)
kk = note number: 00H - 7FH (0 - 127)
vv = note on velocity: 01H - 7FH (1 - 127)
* With the Trigger Mode is set to "Shot", Note On message is transmitted when you strike the
pad.
* With the Trigger Mode is set to "Gate", Note On message is transmitted when you strike the
pad.
* With the Trigger Mode is set to "Trig", Note On and Note Off messages are alternately
transmitted when you strike the pad.
* On the channel assigned to the pad part and the percussion parts, the note numbers
specified by the patch will be transmitted.
●Polyphonic Key Pressure
Status 2nd byte 3rd byte
AnH kkH vvH
n = MIDI channel number: 0H - FH (ch.1 - ch.16)
kk = note number: 00H - 7FH (0 - 127)
vv = pressure: 00H - 7FH (0 - 127)
* The HPD-15 tramsmits a value corresponding to the pressing force of the pad.
* This will not be transmitted if the MuteTx, PitchTx and CtrlTx are set to "OFF".
* This is transmitted only on the channel which is assigned to the pad part and the
percussion parts.
* Transmitted when the HPD-15 is in play for pattern in which this message is recorded.
●Control Change
❍Bank Select (Controller number 0, 32)
Status 2nd byte 3rd byte
BnH 00H mmH
BnH 20H llH
n = MIDI channel number: 0H - FH (ch.1 - ch.16)
mm = Bank number MSB: 00H - 02H (bank1:user patch bank bank2,3:preset patch)
ll = Bank number LSB: processed as 00H
* Bank Select corresponding to patch are sent when patch are selected.
* Bank Select corresponding to each part's instrument are sent when patterns is selected.
Also, when instruments are selected for parts,bank select for the respective instruments
are sent.
- Owner’s Manual 1
- IMPORTANT NOTES 4
- Contents 5
- Features 8
- How To Use This Manual 9
- Panel Descriptions 10
- Rear Panel 11
- Chapter 1 Quick Start 13
- Listening to the Demo Song 14
- Performing 15
- P01 LATIN 17
- 01 Conga 17
- P02 AFRICAN 17
- 01 TalkingDrm 17
- P05 ORCH 18
- 01 Vibraphone 18
- A1* PITCH +600 19
- Distortion (Multi-Effects) 20
- U0101A* PAD SET 25
- Pitch +200cent 25
- Playing Back a Preset Pattern 26
- Tempo =100 27
- System Settings 28
- CONTROLLER 29
- DBEAM Sens 100 29
- 3 124, 5 30
- When you select the 31
- Try to Play the Conga 34
- Chapter 2 Modifying a Patch 35
- Adjusting Sounds 36
- Chapter 2 37
- Adding Cyclic Change to the 38
- Effect Settings 39
- U0101 MULTI-FX 40
- Type# Hall"A" 40
- Stereo Equalizer (Stereo EQ) 41
- Ring Modulator (RingModltr) 44
- Stereo Chorus (Stereo Cho) 44
- Tetra Chorus (TetraChorus) 45
- Tremolo Chorus (Tremolo Cho) 45
- Stereo Flanger (Stereo Fln) 46
- Step Flanger (StepFlanger) 47
- Stereo Delay (StereoDelay) 48
- Modulation Delay (Mod Delay) 49
- Advanced Reverb (AdvanceRev) 51
- Gate Reverb (GateReverb) 51
- Controlling the Tone 52
- Using a Pad to Start a 54
- Set the Volume of the Entire 54
- Settings for Other Functions 54
- Setting for MIDI 55
- Transmission 55
- Naming a Patch 55
- Saving Your Settings (Write) 56
- Duplicating Settings (Copy) 56
- Copying a Value to All Pads 58
- Using Realtime Modify to 58
- Adjust Values 58
- Basic Settings for Recording 59
- Settings for the Pattern 60
- Chapter 3 61
- Rehearsal Function 62
- Changing the Settings of 63
- Editing a Pattern 64
- Creating a Patch Chain 65
- (Chain Edit) 65
- Playing with a Patch Chain 66
- (Chain Play) 66
- Settings for basic operation 67
- Settings for the Controllers 69
- Turning On/Off the D Beam 69
- Turning On/Off the Ribbons 69
- Setting the Pad Sensitivity 70
- Chapter 5 71
- Settings for the Pedal 72
- P0606A3*PAD INST 72
- R70:13" Hi-Hat 72
- P0606PL*PAD INST 72
- PEDAL(A3) 72
- (see figure on p. 37) 74
- MIDI Settings 75
- Restoring Settings to Their 75
- Default Values (Factory 75
- Using the HPD-15 to Play 76
- External Instruments 76
- Setting the MIDI Channels 77
- Using the HPD-15 As a 78
- Sound Module 78
- Soft Thru OFF 79
- MIDI Instrument 80
- Saving Data to an External 80
- Receiving (Bulk Load) 81
- Setting the Device ID 82
- Program Change Number List 82
- (User Patches) 82
- Device ID 17 82
- Troubleshooting 83
- MIDI-related Problems 84
- Sequencer-related Problems 84
- Procedure for Factory Reset 85
- Messages and Error Messages 86
- Messages 87
- About MIDI 88
- How the Internal Sequencer 89
- Operates 89
- Preset Patch List 90
- Preset Pattern List 91
- Instrument List 92
- Pad Set Instrument List 94
- Backing Instrument List 94
- Effect Type List 95
- Demo Song List 96
- MIDI Implementation 100
- Appendices 101
- 2. Transmit data 101
- 3. Parameter address map 104
- (Model ID = 00H 2EH) 104
- 4. Bulk Dump 108
- 5. Supplementary material 108
- MIDI Implementation Chart 110
- Specifications 112
- USING THE UNIT SAFELY 115
© 2020, manymanuals.com. All rights reserved. | 2.849 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals