Roland HPD-15 User Manual download pdf (Page 40)

Chapter 2 Modifying a Patch

Adjusting the Multi-Effect Settings

Multi-effect (M-FX) allows you to select different algorithms

to obtain a variety of effects.

Parameter Category: MULTI-FX

fig.2-14

Type: Refer to MULTI-FX Type (p. 95)

Selects the preset setting of multi-effects.

If you wish to make even more detailed settings, adjust the

algorithm below and parameters on the following pages.

When you change a value, a “#” will appear beside the

“Type.”

Algo:

Selects the algorithm of the effect. The parameters and values

will differ depending on the algorithm.

Stereo EQ: Stereo Equalizer (Modify the tone)

CompLimiter: Compressor/Limiter (Make the volume

more consistent)

Enhancer: Enhancer (Add sparkle to the sound)

Spectrum: Spectrum (Add character to the sound)

Isolator: Isolator (Cut off a specific frequency range)

DynamicFltr: Dynamic Filter (Modify the tone according

to the volume)

Sustainer:

Sustainer (Increase the duration of the sound)

Overdrive: Overdrive (Mildly distort the sound)

Distortion: Distortion (Severely distort the sound)

Lo-Fi: Lo-Fi (Simulate a “low-fidelity” sound)

RingModltr: Ring Modulator (Give the sound a metallic

character)

Stereo Cho: Stereo Chorus (Add depth and

spaciousness to the sound)

TetraChorus: Tetra Chorus (Layer chorus sounds to

create more spaciousness)

Tremolo Cho: Tremolo Chorus (Cyclically modulate the

volume to create spaciousness)

Space D: Space D (Add transparent spaciousness)

Stereo Fln: Stereo Flanger (Add metallic resonance to

the sound)

StepFlanger: Step Flanger (Add metallic resonance

while shifting the pitch by steps)

Phaser: Phaser (Give the sound a “swooshing”

character)

FbackPitch: Feedback Pitch Shifter (Shift the pitch)

StereoDelay: Stereo Delay (Delay the sound)

Mod Delay: Modulation Delay (Delay the sound while

modulating it)

TimeCtrlDly: Time Control Delay (Control the delay and

pitch in realtime)

3TapDlySht: 3-tap delay short (Delay the sound in three

directions)

3TapDlyLng: 3-tap delay Long

4TapDlySht: 4-tap delay short (Produce four delayed

sounds)

4TapDlyLng: 4-tap delay Long

AdvanceRev:

Advanced Reverb (Add reverb to the sound)

GateReverb:

Gate Reverb (Sharply cut the reverberation)

The parameters of each algorithm are explained on the

following pages.

In the explanation on the following pages, the value of

parameters marked with “RTM” can be controlled by [M-FX

DEPTH] of the Realtime Modify (p. 19).

* If you modify the MULTI-FX DEPTH in EZ Edit Mode (p.

25), the value of these parameters will be changed.

In the explanation on the following pages, the value of

parameters marked with “LFO” can be controlled by the

LFO. For details, refer to “Adding Cyclic Change to the

Tone” (p. 38).

In the explanation on the following pages, the value of

parameters marked by “Ctrl1, Ctrl2, Ctrl3” can be controlled by

the pads, D Beam, and ribbons. For details, refer to the section

CtrlTx: MFX Ctrl 1–3

in “Controlling the tone” (p. 52).

FxOut Volume:

Adjusts output volume of the multi-effects.

Fx Rev Send:

Adjusts the depth of reverb applied to the sound processed

by the multi-effects.

If you change the “Type,” the algorithm of the effect and the

values of the parameters will be changed to the setting of

each type.

U0101 MULTI-FX

Type# Hall"A"

1 2 ... 35 36 37 38 39 40 41 42 43 44 45 ... 115 116

Comments to this Manuals

No comments

Roland HPD-15 User Manual Page 40

Comments to this Manuals