Roland XP-80 Owner's Manual Page 213
- Page / 244
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
❍ Expression (Controller number 11)
status 2nd byte 3rd byte
BnH 0BH vvH
n=MIDI channel number : 0H - FH (ch.1 - ch.16)
vv=Expression : 00H - 7FH (0 - 127)
* If the Volume parameter (SYSTEM/Control/Control Source) is set to
VOL&EXP, the volume of the Part corresponding to the MIDI channel of the
received message will be adjusted. However this is not received if the
Volume parameter (PATCH/LFO&Ctl/Control Switch) is OFF.
* In GM mode, the volume can always be controlled.
❍ Hold 1 (Controller number 64)
status 2nd byte 3rd byte
BnH 40H vvH
n=MIDI channel number : 0H - FH (ch.1 - ch.16)
vv=control value : 00H - 7FH (0 - 127) 0-63=OFF, 64-127=ON
* Not received when the Hold-1 parameter (PATCH/LFO&Ctl/Control Switch)
is OFF.
❍ Portamento (Controller number 65)
status 2nd byte 3rd byte
BnH 41H vvH
n=MIDI channel number : 0H - FH (ch.1 - ch.16)
vv=control value : 00H - 7FH (0 - 127) 0-63=OFF, 64-127=ON
* The Switch parameter (PATCH/Common/Common Control) will change.
❍ Sostenuto (Controller number 66)
status 2nd byte 3rd byte
BnH 42H vvH
n=MIDI channel number : 0H - FH (ch.1 - ch.16)
vv=control value : 00H - 7FH (0 - 127) 0-63=OFF, 64-127=ON
❍ Soft (Controller number 67)
status 2nd byte 3rd byte
BnH 43H vvH
n=MIDI channel number : 0H - FH (ch.1 - ch.16)
vv=control value : 00H - 7FH (0 - 127) 0-63=OFF, 64-127=ON
❍ Hold 2 (Controller number 69)
status 2nd byte 3rd byte
BnH 45H vvH
n=MIDI channel number : 0H - FH (ch.1 - ch.16)
vv=control value : 00H - 7FH (0 - 127)
❍ Sound Controller 2 (Controller number 71)
status 2nd byte 3rd byte
BnH 47H kkH
n=MIDI channel number : 0H - FH (ch.1 - ch.16)
vv=control value : 00H - 40H - 7FH (-128 - 0 - +126)
* The Resonance parameter (PATCH/TVF/TVF Param) will change relative-
ly.
❍ Sound Controller 3 (Controller number 72)
status 2nd byte 3rd byte
BnH 48H kkH
n=MIDI channel number : 0H - FH (ch.1 - ch.16)
vv=control value : 00H - 40H - 7FH (-128 - 0 - +126)
* The Time 2—4 parameter (PATCH/TVF/TVF Envelope) , The Time 2—4
parameter (PATCH/TVA/TVA Envelope)will change relatively.
❍ Sound Controller 4 (Controller number 73)
status 2nd byte 3rd byte
BnH 49H kkH
n=MIDI channel number : 0H - FH (ch.1 - ch.16)
vv=control value : 00H - 40H - 7FH (-128 - 0 - +126)
* The Time 1 parameter (PATCH/TVF/TVF Envelope) , The Time 1 parame-
ter (PATCH/TVA/TVA Envelope)will change relatively.
❍ Sound Controller 5 (Controller number 74)
status 2nd byte 3rd byte
BnH 4AH kkH
n=MIDI channel number : 0H - FH (ch.1 - ch.16)
vv=control value : 00H - 40H - 7FH (-64 - 0 - +63)
* The Cutoff Frequency parameter (PATCH /TVF/TVF Param) will change
relatively.
❍ General Purpose Controller 5 (Controller number 80)
status 2nd byte 3rd byte
BnH 50H kkH
n=MIDI channel number : 0H - FH (ch.1 - ch.16)
vv=control value : 00H - 40H - 7FH (-128 - 0 - +126)
* The Level 1 — 3 parameter (PATCH/TVA/TVA Param) of Tone 1 will
change relatively.
❍ General Purpose Controller 6 (Controller number 81)
status 2nd byte 3rd byte
BnH 51H kkH
n=MIDI channel number : 0H - FH (ch.1 - ch.16)
vv=control value : 00H - 40H - 7FH (-128 - 0 - +126)
* The Level 1 — 3 parameter (PATCH/TVA/TVA Param) of Tone 2 will
change relatively.
❍ General Purpose Controller 7 (Controller number 82)
status 2nd byte 3rd byte
BnH 52H kkH
n=MIDI channel number : 0H - FH (ch.1 - ch.16)
vv=control value : 00H - 40H - 7FH (-128 - 0 - +126)
* The Level 1 — 3 parameter (PATCH/TVA/TVA Param) of Tone 3 will
change relatively.
❍ General Purpose Controller 8 (Controller number 83)
status 2nd byte 3rd byte
BnH 53H kkH
n=MIDI channel number : 0H - FH (ch.1 - ch.16)
vv=control value : 00H - 40H - 7FH (-128 - 0 - +126)
* The Level 1 — 3 parameter (PATCH/TVA/TVA Param) of Tone 4 will
change relatively.
❍ Portamento Control (Controller number 84)
status 2nd byte 3rd byte
BnH 54H kkH
n=MIDI channel number : 0H - FH (ch.1 - ch.16)
kk=source note number : 00H - 7FH (0 - 127)
* A Note On message received immediately after a Portamento control will
be sounded with the pitch changing smoothly from the source note number.
If a voice is already sounding at the same note number as the source note
number, that voice will change pitch to the pitch of the newly received Note
On, and continue sounding (i.e., will be played legato).
* The speed of the pitch change caused by Portamento is determined by the
Time parameter (PATCH/Common/Common Control) value.
❍ Effect 1 (Reverb Send Level) (Controller number 91)
status 2nd byte 3rd byte
BnH 5BH vvH
n=MIDI channel number : 0H - FH (ch.1 - ch.16)
vv=Reverb Send Level : 00H - 7FH (0 - 127)
* Not received in Patch mode.
❍ Effect 3 (Chorus Send Level) (Controller number 93)
status 2nd byte 3rd byte
BnH 5DH vvH
n=MIDI channel number : 0H - FH (ch.1 - ch.16)
vv=Chorus Send Level : 00H - 7FH (0 - 127)
* Not received in Patch mode.
215
Chapter 12. Supplementary material
- USING THE UNIT SAFELY 1
- Important notes 2
- Before Using Floppy Disks 3
- Usinng The Printed Circuit 3
- Features of the XP-80 4
- Chapter outlines 5
- Contents 6
- Front panel 12
- I. SEQUENCER section 13
- Side panel 14
- Rear panel 15
- XP-80 configuration 16
- Performances 17
- Rhythm Sets 17
- Basic operation 18
- Moving the cursor 21
- Modifying a value 21
- Assigning a name 22
- Chapter 2. Playing 24
- Displaying a Patch list 25
- (turning a Tone on/off) 25
- Changing sound characters 26
- Playing in Performance mode 27
- (Sound Palette) 30
- Playing in Rhythm Set mode 31
- Rhythm Set 32
- Playing an arpeggio 33
- Recording an arpeggio 35
- (Octave Shift) 35
- Regarding effects 37
- Sound editing procedures 38
- Editing a Performance 41
- Editing a Rhythm Set 42
- Keeping edited sound 43
- Functions of Patch parameters 44
- Common Control display 45
- Structure display 47
- Pitch display 50
- Pitch Envelope display 51
- TVF Envelope display 52
- TVA Envelope display 54
- Time 1 Time 2 Time 3 Time 4 54
- Control Switch display 57
- EFX Type name 58
- Chorus display 62
- Reverb display 62
- Common display 63
- Lower Upper 64
- Key range specified for Patch 64
- [PERFORM] 65
- [F4] (MIDI) 65
- [F5] (Effects) 66
- Part Information display 67
- Frequency 69
- Time 1 Time 2 70
- Time 3 Time 4 70
- [RHYTHM] 71
- [F5] (Key Ctl) 71
- 2: OVERDRIVE 72
- 3: DISTORTION 72
- 4: PHASER 73
- 5: SPECTRUM 73
- 6: ENHANCER 73
- 7: AUTO-WAH 74
- 8: ROTARY 74
- 9: COMPRESSOR 74
- 10: LIMITER 75
- 11: HEXA-CHORUS 75
- 12: TREMOLO-CHORUS 75
- 13: SPACE-D 76
- 14: STEREO-CHORUS 76
- 15: STEREO-FLANGER 76
- 16: STEP-FLANGER 77
- 17: STEREO-DELAY 77
- 18: MODULATION-DELAY 78
- 19: TRIPLE-TAP-DELAY 79
- 20: QUADRUPLE-TAP-DELAY 79
- 21: TIME-CONTROL-DELAY 80
- 22: 2VOICE-PITCH-SHIFTER 80
- 24: REVERB 81
- 38: CHORUS/DELAY 86
- 39: FLANGER/DELAY 86
- 40: CHORUS/FLANGER 86
- Setup display 86
- Adjusting tuning (Tune) 87
- [SYSTEM] 87
- [F2] (Tune) 87
- MIDI settings (MIDI) 88
- [F3] (MIDI) 88
- Control Assign display 90
- Pedal Assign display 90
- Arpeggio settings (Arpeg) 91
- [F5] (Arpeg) 91
- System Information display 93
- About the sequencer 94
- Playing back a song 95
- (Quick Play) 96
- Reserve 1 97
- Reserve 2 97
- Reserve 3 97
- Playing back a Pattern 99
- Before you start to record 102
- Selecting instrument sounds 103
- Setting the time signature 103
- Performing realtime recording 106
- (Realtime Erase) 108
- Recording tempo changes 108
- Canceling recording (Undo) 110
- (Step recording) 111
- Inputting data step by step 111
- Inputting chords 112
- Inputting ties 112
- Inputting a dotted note 112
- Inputting rests 112
- Erasing wrong notes 112
- Deleting recording (Undo) 113
- Saving only a song 114
- Chapter 5. Editing a song 115
- Settings for an entire song 116
- Locate function 117
- Setting loop 118
- [SEQUENCER]➞[F5] (Loop) 118
- Editing performance data over 119
- Setting the editing area 120
- [SEQUENCER]➞[F3] (TrkEdit) 120
- Copying a phrase – 3 Copy 122
- (Insert measure) 124
- (Change velocity) 125
- (Change MIDI channel) 126
- (Change gate time) 127
- Aligning a song’s timing 134
- (Quantize) 134
- Grid quantize 135
- Shuffle quantize 136
- Groove quantize 137
- [SEQUENCER]➞[F4] (Micro) 142
- Phrase track/Pattern 144
- Erasing performance data 147
- Moving performance data 147
- Copying performance data 147
- Getting ready to use RPS 148
- Playing using RPS 149
- Getting ready for Chain Play 151
- Saving a chain to disk 152
- Chain play 152
- About Utility mode 153
- Performance write 154
- Patch write 154
- Rhythm Set write 154
- [UTILITY]➞[1]➞[ENTER] 154
- Performance copy 155
- [UTILITY]➞[2]➞[ENTER] 155
- Patch copy 156
- Rhythm Set copy 157
- – 3 Initialize 158
- 4 Data Transfer 159
- [UTILITY]➞[4]➞[ENTER] 160
- [UTILITY]➞[5]/[6]/[7]➞[ENTER] 162
- – 8 Factory (Factory preset) 163
- About Disk mode 164
- XP-80 – 1 Load 165
- Saving data to disk – 2 Save 166
- – 3 Format 167
- 5 Verify 168
- Changing the name of disk – 168
- Deleting unwanted files – 169
- 7 Delete (Delete file) 169
- Renaming a file – 8 Rename 169
- 9 Info (Disk information) 170
- Entering GM mode 171
- Modifying GM mode settings 172
- [SHIFT]+[PERFORM]➞[F6] (Info) 173
- Convenient functions in GM 174
- Transfer (GM Data Transfer) 175
- Techniques for using Patches 176
- Using the XP-80 to play live 177
- OUTPUTLEVEL 178
- CLICK OUT 178
- Changing the Patch 179
- Changing the Performance 179
- Changing the Rhythm Set 179
- Using external MIDI devices 180
- Synchronization with external 181
- MIDI devices 181
- Disk Recorder 182
- MIDI OUT 183
- MIDI OUTMIDI IN 183
- Recording on the XP-80 184
- Troubleshooting 185
- Error messages 186
- Parameter List 188
- WG Group 189
- TVF Group 189
- TVA Group 190
- LFO&Ctl Group 190
- Effects Group 191
- Performance Parameters 192
- Rhythm Set Parameters 193
- Key TVF Group 194
- Key TVA Group 194
- Key Ctl Group 194
- GM Parameters 195
- Info Group 196
- EFX Parameters 197
- System Parameters 202
- Control Group 203
- Arpeg Group 203
- Factory Preset Settings 204
- INT-B (Internal B) 205
- Patch List 206
- GM (GM Group) 208
- Rhythm set List 209
- Performance List 210
- Arpeggio style list 211
- MIDI implementation 212
- ■ Channel Mode messages 214
- ■ System Realtime messages 215
- ■ System Exclusive messages 215
- ■ Channel Voice messages 216
- ■ Channel voice messages 217
- 1-1-1.System Common 220
- 1-1-2.Scale Tune 220
- 1-2.Performance 220
- 1-2-1.Performance Common 221
- 1-2-2.Performance Part 221
- 1-3.Patch 221
- 1-3-1.Patch Common 221
- 1-3-2.Patch Tone 222
- 1-4.Rhythm Setup 223
- 1-4-1.Rhythm Common 223
- 1-4-2.Rhythm Note 223
- 6. Supplementary material 224
- Thus, the address is: 225
- 00 00H Patch Common 226
- MIDI Implementation Chart 227
- Specifications 229
- Quick reference of displays 230
- Performance mode [PERFORM] 231
- Rhythm Set mode [RHYTHM] 232
- GM mode [SHIFT] + [PERFORM] 233
- Sequencer mode [SEQUENCER] 234
- Chain Play mode [CHAIN PLAY] 236
- System mode [SYSTEM] 236
- Utility mode [UTILITY] 237
- Disk mode [DISK] 238
- Information 244
Related products and manuals for Musical Instruments Roland XP-80
Musical Instruments Roland HP508 User Manual
(40 pages)
Musical Instruments Roland RD-700GX User Manual
(149 pages)
(149 pages)
Musical Instruments Roland AT-30 User Manual
(51 pages)
(51 pages)
Musical Instruments Roland SD-90 Owner's Manual
(161 pages)
(161 pages)
Musical Instruments Roland XP-80 User Manual
(39 pages)
(39 pages)
Musical Instruments Roland VG-88 User Manual
(72 pages)
(72 pages)
Musical Instruments Roland FP-9 User Manual
(41 pages)
(41 pages)
Musical Instruments Roland FP-7 User Manual
(184 pages)
(184 pages)
Musical Instruments Roland BR-900CD User Manual
(229 pages)
(229 pages)
Musical Instruments Roland VS-2000 User's Guide
(282 pages)
(282 pages)
Musical Instruments Roland DR-3 User Manual
(121 pages)
(121 pages)
© 2020, manymanuals.com. All rights reserved. | 0.236 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals