Roland XP-80 Owner's Manual download pdf (Page 214)

216

❍ RPN MSB/LSB (Controller number 100,101)

status 2nd byte 3rd byte

BnH 65H mmH

BnH 64H llH

n=MIDI channel number : 0H - FH (ch.1 - ch.16)

mm=MSB of the parameter number specified by RPN

ll=LSB of the parameter number specified by RPN

<<< RPN >>>

Control Changes include RPN (Registered Parameter Numbers), which are

extended parameters whose function is defined in the MIDI specification.

When using RPNs, first the RPN (Controller numbers 100 and 101; they can be

sent in any order) is transmitted to specify the parameter you wish to control.

Then, Data Entry messages (Controller numbers 6 and 38) are used to set the

value of the specified parameter. Once a RPN parameter has been specified,

all further Data Entry messages on that channel are considered to apply to

that specified parameter. In order to prevent accidents, when the desired set-

ting has been made for the parameter, it is recommended that RPN be set to

Null.

This device receives the following RPNs.

RPN Data entry

MSB LSB MSB LSB Notes

00H 00H mmH — Pitch Bend Sensitivity

mm : 00H - 0CH (0 - 12 semitones)

ll : ignored (processed as 00H)

Up to 1 octave can be specified in semitone steps.

*The Bend Range up parameter, Bend Range

Down parameter (PATCH/Common/Common

Control) will also be changed.

*Not received by the Rhythm Part (Part 10).

00H 01H mmH llH Master Fine Tuning

mm, ll : 20 00H - 40 00H - 60 00H ( -8192 *50 /

8192 - 0 - +8192 * 50 / 8192 cent )

*In Patch mode, the Master Tune parameter (SYS-

TEM/Tune/Tune) will change.

*In Performance mode, the Fine Tune parameter

of each Part (PERFORM/Part/Part Param) will

change. When received on the Control channel,

the Master Tune parameter (SYSTEM/Tune/Tune)

will change.

00H 02H mmH — Master Coarse Tuning

mm : 10H - 40H - 70H (-48 - 0 - +48 semitones)

ll : ignored (processed as 00H)

* Not received in Patch mode.

* In Performance mode, the Coarse parameter of

each Part (PERFORM:PART:PART SETTING) will

change.

7FH 7FH — — RPN null

RPN and NRPN will be set as “unspecified”. Once

this setting has been made, subsequent Data Entry

messages will be ignored. (It is not necessary to

transmit Data Entry for RPN Null settings.

Parameter values that were previously set will not

change.

mm, ll : ignored

● Program Change

status 2nd byte

CnH ppH

n=MIDI channel number : 0H - FH (ch.1 - ch.16)

pp=Program number : 00H - 7FH (prog.1 - prog.128)

* Not received when the Rx Program Change parameter (SYSTEM/MIDI/

MIDI Param 2) is OFF.

* When received on the Control channel, the Performance will change.

* Not received in Performance mode when the Rx Switch parameter (PER-

FORM/MIDI/Part MIDI) is OFF.

● Channel Aftertouch

status 2nd byte

DnH vvH

n=MIDI channel number : 0H - FH (ch.1 - ch.16)

vv=Channel Aftertouch : 00H - 7FH (0 - 127)

* Not received in Performance mode when the Rx Switch parameter (PER-

FORM/MIDI/Part MIDI) is OFF.

● Pitch Bend Change

status 2nd byte 3rd byte

EnH llH mmH

n=MIDI channel number : 0H - FH (ch.1 - ch.16)

mm,ll=Pitch Bend value : 00 00H - 40 00H - 7F 7FH (-8192 - 0 - +8191)

* Not received in Performance mode when the Rx Switch parameter (PER-

FORM/MIDI/Part MIDI) is OFF.

■ Channel Mode messages

● All Sound Off (Controller number 120)

status 2nd byte 3rd byte

BnH 78H 00H

n=MIDI channel : 0H - FH (ch.1 - ch.16)

* When this message is received, all notes currently sounding on the corre-

sponding channel will be turned off.

* Not received in Performance mode when the Rx Switch parameter (PER-

FORM/MIDI/Part MIDI) is OFF.

● Reset All Controllers (Controller number 121)

status 2nd byte 3rd byte

BnH 79H 00H

n=MIDI channel number : 0H - FH (ch.1 - ch.16)

* Not received in Performance mode when the Rx Switch parameter (PER-

FORM/MIDI/Part MIDI) is OFF.

* When this message is received, the following controllers will be set to their

reset values.

Controller Reset value

Pitch Bend Change ±0 (center)

Polyphonic Key Pressure 0 (off)

Channel Pressure 0 (off)

Modulation 0 (off)

Breath type 0 (minimum)

Expression 127 (maximum)

However the controller will be at minimum.

Hold 1 0 (off)

Sostenuto 0 (off)

Soft 0 (off)

Hold 2 0 (off)

RPN

Unset. Previously set data will not change.

NRPN

Unset. Previously set data will not change.

System General purpose controller 1 0 (minimum)

System General purpose controller 2 0 (minimum)

● All Note Off (Controller number 123)

status 2nd byte 3rd byte

BnH 7BH 00H

n=MIDI channel number : 0H - FH (ch.1 - ch.16)

* When All Note Off is received, all currently sounding notes of the corre-

sponding channel will be turned off. However if Hold 1 or Sostenuto are on,

the sound will be held until these are turned off.

* Not received in Performance mode if Rx Switch parameter (PERFORM/

MIDI/Part MIDI) is OFF.

● Omni Off (Controller number 124)

status 2nd byte 3rd byte

BnH 7CH 00H

n=MIDI channel number : 0H - FH (ch.1 - ch.16)

* The same processing as when All Note Off is received will be done.

* Not received in Performance mode if Rx Switch parameter (PERFORM/

MIDI/Part MIDI) is OFF.

Chapter 12. Supplementary material

1 2 ... 209 210 211 212 213 214 215 216 217 218 219 ... 243 244

Roland XP-80 Owner's Manual Page 214

Comments to this Manuals

Roland XP-80 Owner's Manual Page 214

Comments to this Manuals

Related products and manuals for Musical Instruments Roland XP-80