Roland VM-C7200 Owner's Manual Page 25
- Page / 100
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
25
Before Mixing Operations
To Change Parameters
To change the value of a parameter, move the cursor to select a parameter,
and use the knobs [V1]-[V6], faders, and/or buttons [F1]-[F6] to change its
value, as described below.
To Move the Cursor
The cursor – a bold rectangle on the display – selects a single parameter or
group of parameters so that their values can be adjusted. To move the
cursor, press CURSOR [UP] [DOWN] [LEFT] [RIGHT].
To Set the Values of Parameters
There are certain rules for setting parameters, as listed below. We
recommend you keep them in mind.
• parameters are set by turning knobs [V1]-[V6]. Turn the knob
below the parameter you wish to change.
• parameters are set by pressing buttons [F1]-[F6]. Press the
button for ON – this highlights the parameter in black on the display
– or OFF (not highlighted) below the parameter you wish to change.
• parameters are set by turning knobs [V1]-[V6] first, and then
pressing buttons [F1]-[F6](SET) to confirm the changes. Use the knob
and button below the parameter you wish to change. (Some
parameters can be set by pressing [F1]-[F6](SET) only.)
• Parameters shown as faders are set using the console’s faders. If the
fader indicated is selected by the cursor, you can also change its
value by turning the corresponding knobs [V1]-[V6].
To Operate on [INPUT] or [MULTI IN] channels
To set the input source’s gain level and the tone, such as using the equalizer
and so on, press [INPUT] or [MULTI IN] to select the type of channel you
wish to setup.
With the selected button lit in red, you can control the behavior of each
source signal using the console’s faders or display controls.
The cursor does not appear
on a display where no
cursor selection is needed.
ON OFF
If you want to display or
change frequently used
parameters, or the value of
a single parameter on all of
the channels at once, you
can do this more easily by
using the console’s faders
(Owner’s Manual “Useful
Functions” p.58).
- QUICK START 1
- Table of Contents 2
- Getting Started 4
- Mixing System 5
- Connections 7
- Turning On the Power 10
- LEVEL METER 12
- Setting the Internal Clock 14
- Preparing a Memory Card 16
- To Create a New Project 19
- Turning Off the Power 20
- Before Mixing Operations 22
- 2. Busses / Output Routes 23
- How to Operate This System 24
- To Change Parameters 25
- Mixing Operations 26
- SHIFT3,5 28
- Stereo Balance 30
- Owner’s Manual 32
- “Adjusting Various 32
- Channel Settings 32
- (Equalizer, etc.)” (p.78) 32
- To turn off the equalizer 33
- ON” returns to normal 33
- Setting Up a Monitor 34
- Press [F6](EXIT) to exit 35
- Coupling Adjacent Channels 36
- Muting a Channel 38
- Storing a Project 39
- Using Sub Outputs 40
- (Talkback) 42
- Flex Bus 43
- Flex Bus Output (Internal) 46
- Sending Signals to a Flex Bus 48
- Using On-Board Effects 50
- Send-Return Loop Effect 51
- Go to QUICK START : p.43 53
- (MASTER FX)] for MASTER FX 54
- Selecting the Effects 58
- (Channel Delay) 60
- You can also use the 61
- Other Important Features 62
- Press [F3](REGIST) 63
- To Recall a Scene 64
- Press [F1](RECALL) 65
- (Virtual Patchbay) 66
- Multiple Channels 68
- You can also mute a Fader 69
- Group in the same way as a 69
- [MUTE] (QUICK START: 69
- [1] ~ [9] buttons 70
- Some Special Features 72
- 5.1 Surround 73
- Speaker Modeling 74
- Using EZ Routing Templates 75
- Adjust the effects 79
- About The Word Clock 80
- To Send Signals to a FlexBus 81
- 8 Track Digital Recording 81
- The 8 Track Mixdown Procedure 81
- Set the channel levels 84
- Set up the monitors 84
- Owner’s Manual “Setting a 85
- Connection Samples 88
- ..MEMO 97
Related products and manuals for Processors Roland VM-C7200
Processors Roland VM-C7200 Owner's Manual
(32 pages)
(32 pages)
Processors Roland VM-C7200 Owner's Manual
(80 pages)
(80 pages)
Processors Roland PC-300 User Manual
(14 pages)
(14 pages)
Processors Roland AR-1000 Owner's Manual
(50 pages)
(50 pages)
Processors Roland AR-1000 Owner's Manual
(28 pages)
(28 pages)
Processors Roland AR-1000 Owner's Manual
(72 pages)
(72 pages)
Processors Roland VF-1 User Manual
(143 pages)
(143 pages)
Processors Roland A-30 User Manual
(1 pages)
(1 pages)
Processors Roland GT-6B User Manual
(26 pages)
(26 pages)
Processors Roland CE-20 User Manual
(32 pages)
(32 pages)
Processors Roland PC-300 User Manual
(1 pages)
(1 pages)
© 2020, manymanuals.com. All rights reserved. | 0.272 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals