Roland VM-C7200 Owner's Manual Page 84
- Page / 100
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
84
Using EZ Routing Templates
6
Set the channel levels.
1. Press [CH LEVEL].
2. Adjust each channel’s output level using its fader.
7
Set up the monitors.
• The signals from Flex Busses 11 and 12 are sent to STUDIO 1 and 2.
You can send and balance the signals to Flex Busses 11 and 12,
according to the performers’ needs.
8
Adjust the effects.
1. Press [EFFECTS 1-8].
2. Press CURSOR [UP] [DOWN] to navigate to the field showing the
desired effect’s name, and press [F2] [F4] or [F6] to select the effect.
• The following are the effects chosen by the “Live Jazz” template in a
system with three optional VS8F-2 Effects Expansion Boards (sold
separately) installed. The number of available effects listed below
will depend on the number of the VS8F-2s installed.
FX1: GRAPHIC EQUALIZER (P036)
This effect is inserted on the Main out L/R signals. Use it in conjunction with
the Spectrum Analyzer (Owner’s Manual “Using the Spectrum Analyzer”
p.184) to tune the system to the frequency characteristics of the concert hall
or club in which you are working.
FX2: OFF
FX3: REVERB (P000)
This is a general-purpose reverb inserted on Flex Bus 3, to which Channels
1-5, 8, 11-16, 19-20 are routed.
To add reverb to a channel’s signal, turn up the channel’s send level to Flex
Bus 3 until the desired amount of reverb is applied.
FX4: COMPRESSOR (P038)
The left channel of this dual-mono compressor provides compression for the
Bass Drum (Ch 1). Its right side supplies compression for the Snare Drum
(Ch 2).
FX5: OFF
FX6: COMPRESSOR (P038)
The left channel of this dual-mono compressor provides compression for
Vocal 1 (Ch 19). Its right side supplies compression for Vocal 2 (Ch 20).
FX7: COMPRESSOR (P038)
The left channel of this dual-mono compressor provides compression for
Bass 1 (Ch 9). Its right side supplies compression for Bass 2 (Ch 10).
3. Use CURSOR [UP] [DOWN], [PAGE UP] [PAGE DOWN], [V1]-[V6] and
[F1]-[F6] to adjust the effects.
Owner’s Manual “Setting
up ON/OFF, SEND LEVEL
and PAN for a Channel”
(p.70)
Owner’s Manual “Mixing
Procedure 2 (Output and
Monitor)” (p.84)
Owner’s Manual “Using
the Internal Effects” (p.109)
- QUICK START 1
- Table of Contents 2
- Getting Started 4
- Mixing System 5
- Connections 7
- Turning On the Power 10
- LEVEL METER 12
- Setting the Internal Clock 14
- Preparing a Memory Card 16
- To Create a New Project 19
- Turning Off the Power 20
- Before Mixing Operations 22
- 2. Busses / Output Routes 23
- How to Operate This System 24
- To Change Parameters 25
- Mixing Operations 26
- SHIFT3,5 28
- Stereo Balance 30
- Owner’s Manual 32
- “Adjusting Various 32
- Channel Settings 32
- (Equalizer, etc.)” (p.78) 32
- To turn off the equalizer 33
- ON” returns to normal 33
- Setting Up a Monitor 34
- Press [F6](EXIT) to exit 35
- Coupling Adjacent Channels 36
- Muting a Channel 38
- Storing a Project 39
- Using Sub Outputs 40
- (Talkback) 42
- Flex Bus 43
- Flex Bus Output (Internal) 46
- Sending Signals to a Flex Bus 48
- Using On-Board Effects 50
- Send-Return Loop Effect 51
- Go to QUICK START : p.43 53
- (MASTER FX)] for MASTER FX 54
- Selecting the Effects 58
- (Channel Delay) 60
- You can also use the 61
- Other Important Features 62
- Press [F3](REGIST) 63
- To Recall a Scene 64
- Press [F1](RECALL) 65
- (Virtual Patchbay) 66
- Multiple Channels 68
- You can also mute a Fader 69
- Group in the same way as a 69
- [MUTE] (QUICK START: 69
- [1] ~ [9] buttons 70
- Some Special Features 72
- 5.1 Surround 73
- Speaker Modeling 74
- Using EZ Routing Templates 75
- Adjust the effects 79
- About The Word Clock 80
- To Send Signals to a FlexBus 81
- 8 Track Digital Recording 81
- The 8 Track Mixdown Procedure 81
- Set the channel levels 84
- Set up the monitors 84
- Owner’s Manual “Setting a 85
- Connection Samples 88
- ..MEMO 97
Related products and manuals for Processors Roland VM-C7200
Processors Roland VM-C7200 Owner's Manual
(32 pages)
(32 pages)
Processors Roland VM-C7200 Owner's Manual
(80 pages)
(80 pages)
Processors Roland PC-300 User Manual
(14 pages)
(14 pages)
Processors Roland AR-1000 Owner's Manual
(50 pages)
(50 pages)
Processors Roland AR-1000 Owner's Manual
(28 pages)
(28 pages)
Processors Roland AR-1000 Owner's Manual
(72 pages)
(72 pages)
Processors Roland VF-1 User Manual
(143 pages)
(143 pages)
Processors Roland A-30 User Manual
(1 pages)
(1 pages)
Processors Roland GT-6B User Manual
(26 pages)
(26 pages)
Processors Roland CE-20 User Manual
(32 pages)
(32 pages)
Processors Roland PC-300 User Manual
(1 pages)
(1 pages)
© 2020, manymanuals.com. All rights reserved. | 0.092 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals