Roland MC-505 Owner's Manual download pdf (Page 60)

●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●

Example of settings

Using LFO2 to apply vibrato controlled by the modu-

lation lever

fig.3-84

For each tone, set the LFO2 Pitch Depth to Ò0,Ó and the

LFO2 Rate to approximately Ò90Ó (p. 54, 52).

Using the modulation lever to change the cutoff fre-

quency

fig.3-85

Set the cutoff frequency of each tone to approximately

Ò60Ó (p. 40).

Using the pitch bend lever to change the panning

fig.3-86

For each tone, set the Tone Pan to Ò0,Ó and the Bend

Range Up/Down to Ò0Ó (p. 46, 60).

Using aftertouch to bend down

fig.3-87

Set the Bend Range Down to Ò-48Ó (p. 60).

Saving Patches YouÕve

Created (Patch Write)

After youÕve created a patch you like, do this to save it

as a User Patch:

1. Make sure the pattern is stopped.

2. Press [PATCH] to access the Patch Select

page.

If youÕve modified the patch settings, an asterisk Ò*Ó

will be displayed at the left of the number, indicating

that the selected patch has been modified (edited).

Be aware that if you select a different patch without

saving the modified patch, your changes will be lost.

3. Press [WRITE].

The following display will appear, and the Ò_Ó (cur-

sor) will appear under the number.

fig.3-88

If you do not wish to change the number or name, you

can omit steps 4Ð8.

If you decide not to save the patch, press [EXIT].

4. Press [USER] or [CARD] to select the save

destination bank.

* CARD banks can be selected only if an optional memory

card is inserted.

☞ ÒUsing Memory CardsÓ (p. 159)

5. Use [INC] [DEC] or the [VALUE] dial to select

the save destination number.

At this time, you can press [UNDO/REDO] to check

the name of the patch that is currently in the save des-

tination number. After you have found a patch that

you do not mind overwriting, press [UNDO/REDO]

once again to return to the previous display.

6. Press PAGE [>].

The cursor will move to the beginning of the second

line in the display.

fig.3-89

7. Assign a name to the patch.

Use [INC] [DEC] or the [VALUE] dial to specify the

character.

The following characters can be selected:

Space, AÐZ, aÐz, 0Ð9, ! Ò # $ % & Ô ( ) * +, - . / : ; < = > ?

@ [ ´ ] ^ _ ` { | }

8. Repeat steps 6Ð7 to input the name.

By pressing PAGE [<] you can move the cursor back

toward the left.

A name of up to 12 characters can be input.

9. Press [ENTER].

The confirmation screen will appear in the display.

If you decide to cancel the operation, press [EXIT].

fig.3-90

WRITE

INITIALIZE

Chapter 3. Creating Original Sounds (Patch Edit/Rhythm Edit)

1 2 ... 55 56 57 58 59 60 61 62 63 64 65 ... 257 258

Comments to this Manuals

No comments

Roland MC-505 Owner's Manual Page 60

Comments to this Manuals

Related products and manuals for Audio mixers Roland MC-505