Roland XP-60 Owner's Manual Page 184
- Page / 216
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
184
MIDI Implementation
❍Balance (Controller number 8)
status 2nd byte 3rd byte
BnH 08H vvH
n=MIDI channel number: 0H - FH (ch.1 - ch.16)
vv=Balance: 00H - 7FH (0 - 127)
❍Panpot (Controller number 10)
status 2nd byte 3rd byte
BnH 0AH vvH
n=MIDI channel number: 0H - FH (ch.1 - ch.16)
vv=Panpot: 00H - 40H - 7FH (left - center - right)
* Adjust the stereo location over 128 steps, where 0 is far left, 64 is center, and 127 is far
right. However this is not received when the Pan parameter (PATCH/CONTROL/
RxSWITCH) is OFF.
❍Expression (Controller number 11)
status 2nd byte 3rd byte
BnH 0BH vvH
n=MIDI channel number: 0H - FH (ch.1 - ch.16)
vv=Expression: 00H - 7FH (0 - 127)
* If the Volume parameter (SYSTEM/CONTROL/CONTROL SOURCE) is set to
VOL&EXP, the volume of the Part corresponding to the MIDI channel of the received
message will be adjusted. However this is not received if the Volume parameter
(PATCH/CONTROL/RxSWITCH) is OFF.
* In GM mode, the volume can always be controlled.
❍Hold 1 (Controller number 64)
status 2nd byte 3rd byte
BnH 40H vvH
n=MIDI channel number: 0H - FH (ch.1 - ch.16)
vv=control value: 00H - 7FH (0 - 127) 0-63=OFF, 64-127=ON
* Not received when the Hold-1 RxSwitch parameter (PATCH/CONTROL/DAMPER) is
OFF.
❍Portamento (Controller number 65)
status 2nd byte 3rd byte
BnH 41H vvH
n=MIDI channel number: 0H - FH (ch.1 - ch.16)
vv=control value: 00H - 7FH (0 - 127) 0-63=OFF, 64-127=ON
* The Sw parameter (PATCH/CONTROL/PORTAMENTO) will change.
❍Sostenuto (Controller number 66)
status 2nd byte 3rd byte
BnH 42H vvH
n=MIDI channel number: 0H - FH (ch.1 - ch.16)
vv=control value: 00H - 7FH (0 - 127) 0-63=OFF, 64-127=ON
❍Soft (Controller number 67)
status 2nd byte 3rd byte
BnH 43H vvH
n=MIDI channel number: 0H - FH (ch.1 - ch.16)
vv=control value: 00H - 7FH (0 - 127) 0-63=OFF, 64-127=ON
❍Hold 2 (Controller number 69)
status 2nd byte 3rd byte
BnH 45H vvH
n=MIDI channel number: 0H - FH (ch.1 - ch.16)
vv=control value: 00H - 7FH (0 - 127)
* A hold movement isn't done.
❍Sound Controller 2 (Controller number 71)
status 2nd byte 3rd byte
BnH 47H vvH
n=MIDI channel number: 0H - FH (ch.1 - ch.16)
vv=control value: 00H - 40H - 7FH (-128 - 0 - +126)
* The Res parameter (PATCH/TVF/FILTER) will change relatively.
❍Sound Controller 3 (Controller number 72)
status 2nd byte 3rd byte
BnH 48H vvH
n=MIDI channel number: 0H - FH (ch.1 - ch.16)
vv=control value: 00H - 40H - 7FH (-128 - 0 - +126)
* The T2–4 parameter (PATCH/TVF/TVF ENVELOPE), The T2–4 parameter (PATCH/
TVA/TVA ENVELOPE) will change relatively.
❍Sound Controller 4 (Controller number 73)
status 2nd byte 3rd byte
BnH 49H vvH
n=MIDI channel number: 0H - FH (ch.1 - ch.16)
vv=control value: 00H - 40H - 7FH (-128 - 0 - +126)
* The T1 parameter (PATCH/TVF/TVF ENVELOPE), The T1 parameter (PATCH/TVA/
TVA ENVELOPE) will change relatively.
❍Sound Controller 5 (Controller number 74)
status 2nd byte 3rd byte
BnH 4AH vvH
n=MIDI channel number: 0H - FH (ch.1 - ch.16)
vv=control value: 00H - 40H - 7FH (-64 - 0 - +63)
* The Cut parameter (PATCH/TVF/FILTER) will change relatively.
❍General Purpose Controller 5 (Controller number 80)
status 2nd byte 3rd byte
BnH 50H vvH
n=MIDI channel number: 0H - FH (ch.1 - ch.16)
vv=control value: 00H - 40H - 7FH (-128 - 0 - +126)
* The L1–3 parameter (PATCH/TVA/TVA ENVELOPE) of Tone 1 will change relatively.
❍General Purpose Controller 6 (Controller number 81)
status 2nd byte 3rd byte
BnH 51H vvH
n=MIDI channel number: 0H - FH (ch.1 - ch.16)
vv=control value: 00H - 40H - 7FH (-128 - 0 - +126)
* The L1–3 parameter (PATCH/TVA/TVA ENVELOPE) of Tone 2 will change relatively.
❍General Purpose Controller 7 (Controller number 82)
status 2nd byte 3rd byte
BnH 52H vvH
n=MIDI channel number: 0H - FH (ch.1 - ch.16)
vv=control value: 00H - 40H - 7FH (-128 - 0 - +126)
* The L1–3 parameter (PATCH/TVA/TVA ENVELOPE) of Tone 3 will change relatively.
❍General Purpose Controller 8 (Controller number 83)
status 2nd byte 3rd byte
BnH 53H vvH
n=MIDI channel number: 0H - FH (ch.1 - ch.16)
vv=control value: 00H - 40H - 7FH (-128 - 0 - +126)
* The L1–3 parameter (PATCH/TVA/TVA ENVELOPE) of Tone 4 will change relatively.
❍Portamento Control (Controller number 84)
status 2nd byte 3rd byte
BnH 54H kkH
n=MIDI channel number: 0H - FH (ch.1 - ch.16)
kk=source note number: 00H - 7FH (0 - 127)
* A Note On message received immediately after a Portamento control will be sounded
with the pitch changing smoothly from the source note number. If a voice is already
sounding at the same note number as the source note number, that voice will change
pitch to the pitch of the newly received Note On, and continue sounding (i.e., will be
played legato).
* The speed of the pitch change caused by Portamento is determined by the Time
parameter (PATCH/CONTROL/PORTAMENTO) value.
- OWNER’S MANUAL 1
- IMPORTANT SAFETY INSTRUCTIONS 2
- SAVE THESE INSTRUCTIONS 2
- USING THE UNIT SAFELY 4
- Important Notes 5
- Contents 10
- Main Features 11
- Front and Rear Panel 12
- ■ Rear Panel 14
- Quick Start 15
- Getting Ready 16
- “Turning On the Power” (p 18
- “Turning Off 19
- Outil d'installation 22
- “Turning 23
- Off the Power” (p. 26) et 23
- Making Connections 24
- “Connecting to Your 25
- Computer” (p. 134) 25
- Turning On the Power 26
- (Factory Reset) 27
- Listening to the Demo Song 28
- ■ Profile of the Composer 29
- Playing the Sounds 30
- (Patch Search Function) 32
- Try Out Performance Functions 34
- ■ Hold Pedal 35
- ■ Expression Pedal 35
- ■ Portamento 35
- 516 2,4,5,7 36
- Advanced Use 39
- XP-30 Configuration 40
- Performance 41
- Basic Operation 42
- ■ About the Function Buttons 43
- ■ About the Cursor Buttons 44
- ■ Modifying a Value 45
- ■ Assigning a Name 46
- Chapter 2. Playing 47
- Chapter 2 49
- Playing in Performance Mode 51
- ■ Playing Along with a Song 53
- Playback (XP-30 Used as a 53
- Multitimbral Sound Source) 53
- Sound in Realtime 54
- (Sound Palette Function) 54
- Playing in Rhythm Set Mode 55
- Playing an Arpeggio 56
- ■ Playing an Arpeggio Over a 57
- Preset Keyboard Area 57
- Using a Hold Pedal 58
- Convenient Functions for 59
- Semitone Steps (Transpose) 60
- Note Does Not Sound (Panic) 60
- Regarding Effects 61
- Sound Editing Procedures 62
- Note on Tone Editing 64
- ■ Editing a Performance 65
- ■ Editing a Rhythm Set 66
- Keeping Edited Sound 67
- Functions of Patch Parameters 68
- VELOCITY (Velocity Range) 69
- KEY RANG (Key Range) 70
- STRUCT (Structure) 70
- (EFFECTS) 71
- PATCH CHORUS 72
- Sounds Are Played (CONTROL) 73
- RxSWITCH (Receive Switch) 74
- PEAK & HOLD 74
- CONTROL SOURCE 75
- CONTROL 1–3 75
- ■ Modifying Waveform (WAVE) 76
- ■ Modulating Sounds (LFO) 78
- ■ Modifying Pitch (PITCH) 79
- Frequency 80
- T1 T2 T3 T4 81
- LOWER&UPPER 82
- LOWER UPPER 82
- Functions of Performance 83
- Parameters 83
- ■ Setting Effects for a 84
- Performance (EFFECTS) 84
- PERFORM CHORUS 85
- PERFORM REVERB 85
- ■ Controlling How a Rhythm 90
- Tone will Sound with 90
- Controllers (CONTROL) 90
- ■ Modifying Waveform of a 90
- Rhythm Tone (WAVE) 90
- ■ Changing the Volume and 92
- Stereo Location of a Rhythm 92
- Tone (TVA) 92
- Multi-Effects Types 93
- (EFX Parameter) 93
- 4: PHASER 94
- 5: SPECTRUM 94
- 6: ENHANCER 94
- 7: AUTO-WAH 95
- 8: ROTARY 95
- 9: COMPRESSOR 96
- 10: LIMITER 96
- 11: HEXA-CHORUS 96
- 15: STEREO-FLANGER 98
- 16: STEP-FLANGER 98
- 17: STEREO-DELAY 99
- 18: MODULATION-DELAY 99
- 19: TRIPLE-TAP-DELAY 100
- Chapter 3 101
- 20: QUADRUPLE-TAP-DELAY 101
- 21: TIME-CONTROL-DELAY 101
- 22: 2VOICE-PITCH-SHIFTER 102
- 23: FBK-PITCH-SHIFTER 102
- (Feedback Pitch Shifter) 102
- 27: OVERDRIVE→FLANGER 104
- 28: OVERDRIVE→DELAY 104
- 29: DISTORTION→CHORUS 104
- 34: ENHANCER→DELAY 106
- 35: CHORUS→DELAY 106
- 36: FLANGER→DELAY 106
- XP-30 Operating Environment 108
- Setup (System Parameters 108
- ■ Keyboard and Controllers 110
- Settings (CONTROL) 110
- ■ MIDI Settings (MIDI) 112
- ■ Phrase Preview Settings 113
- (PREVIEW) 113
- ■ Adjusting Tuning (TUNE) 113
- ■ Program Change (PGM CHNG) 114
- Installation Status of Wave 114
- Expansion Boards (INFO) 114
- About Utility/Card Mode 115
- Basic Procedure in Utility/ 115
- Card Mode 115
- Storing Sound Data in User 116
- Memory (WRITE) 116
- Copying Sound Source 117
- Settings (COPY) 117
- ■ Rhythm Set Copy 118
- Initializing Sound Source 119
- Settings (INIT) 119
- Transmitting Sound Settings 119
- ■ Transmitting Data to User 120
- Preventing User Memory 121
- Writing Operation (PROTECT) 121
- Memory Card-Related 121
- Settings (CARD) 121
- Loading a File from Memory 122
- Card into the XP-30 (LOAD) 122
- Saving Data to Memory Card 122
- Recalling Factory Default 123
- Settings (FACTORY RESET) 123
- Entering GM Mode 124
- Modifying GM Mode Settings 125
- GM CHORUS 126
- GM REVERB 126
- Convenient Functions in GM 127
- Mode (GM Utility) 127
- ■ Initializing GM Mode (INIT) 128
- Techniques for Using Patches 129
- Using the XP-30 to Play Live 131
- Using External MIDI Devices 132
- Chapter 6 133
- Selecting Patches 133
- Selecting Performances 133
- Selecting Rhythm Sets 133
- Apple Macintosh 134
- ■ Disconnecting the Keyboard 137
- (Local OFF) 137
- Appendices 139
- Troubleshooting 140
- Error Messages 142
- Quick Reference of Procedures 143
- ■ Controller Settings 144
- ■ Saving and Loading Data 145
- ■ Controlling External MIDI 145
- External MIDI Device 146
- Parameter List 147
- CONTROL Group (p. 73) 148
- WAVE Group (p. 76) 148
- LFO Group (p. 78) 148
- ■ Performance Parameters 150
- ■ Rhythm Set Parameters 151
- ■ GM Mode Parameters 153
- ■ EFX Parameters 154
- ■ System Parameters 158
- Waveform List 160
- INT-B (Internal B) 161
- ● XP-A Menu Waveforms 163
- ● XP-C Menu Waveforms 166
- Patch List 168
- ■ B.P.M. CONVERSION TABLE 174
- Rhythm Set List 177
- Performance List 181
- Arpeggio Style List 182
- MIDI Implementation 183
- 3. Parameter Address Map 190
- 4. Supplementary Material 199
- 10 02 00 00H 204
- 00 00H Patch Common 204
- MIDI Implementation Chart 206
- Specifications 207
- For PC (25-pin) 208
- Apparatus containing 215
- Lithium batteries 215
- Information 216
Related products and manuals for Digital pianos Roland XP-60
Digital pianos Roland DP-990F Owner's Manual
(108 pages)
(108 pages)
Digital pianos Roland VR-760 Owner's Manual
(120 pages)
(120 pages)
Digital pianos Roland UM-ONE User Manual
(2 pages)
(2 pages)
Digital pianos Roland MT-90U Owner's Manual
(72 pages)
(72 pages)
Digital pianos Roland BK-9 User Manual
(12 pages)
(12 pages)
Digital pianos Roland SYB-5 User Manual
(28 pages)
(28 pages)
Digital pianos Roland Fantom XR Owner's Manual
(284 pages)
(284 pages)
Digital pianos Roland BK-9 User's Guide
(22 pages)
(22 pages)
Digital pianos Roland E-600 User Manual
(4 pages)
(4 pages)
Digital pianos Roland SH-2 User Manual
(10 pages)
(10 pages)
Digital pianos Roland PK-7A Owner's Manual
(13 pages)
(13 pages)
Digital pianos Roland RD-300GX User Manual
(114 pages)
(114 pages)
Digital pianos Roland UM-ONE User Manual
(2 pages)
(2 pages)
Digital pianos Roland MP-60 User Manual
(1 pages)
(1 pages)
Digital pianos Roland A-88 User Manual
(24 pages)
Digital pianos Roland VK-88 Owner's Manual
(112 pages)
(112 pages)
© 2020, manymanuals.com. All rights reserved. | 0.663 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals