Roland XP-60 Owner's Manual Page 50
- Page / 216
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
50
Chapter 2. Playing
8. Rotate the VALUE dial or press [INC]/[DEC] to make
the setting. For details on the available categories, refer to
page 49.
* This setting is linked with the Category parameter (PATCH/
COMMON/PATCH CATEGORY).
■ Making a Patch Sound Thick or
Thin (Turning a Tone On/Off)
Since a Patch is a combination of up to four Tones, you can
switch unwanted (Tones out of the four) off and get just the
sound of a specific Tone.
* This setting is linked with the Switch parameter (PATCH/
WAVE/WAVE). If you want just one or two Tones to sound in
a Patch, turn the others off and store that setting on a Patch.
This cuts nonessential use of the XP-30’s simultaneous voices.
1. Make sure that the PATCH PLAY display is showing.
2. Make sure that [EDIT] indicator is dark. If it is lit, press
[EDIT].
At this time, the on/off setting of each Tone in the displayed
Patch will be shown by the indicators of TONE SWITCH [1]–
[4]. Those that are lit are on, and those that are dark are off.
3. Use TONE SWITCH [1]–[4] to switch Tones on/off.
■ Playing Single Notes (Solo)
Normally, the XP-30 allows you to play chords. Pressing
[SOLO] allows performance using single notes. This function
is effective when performing a solo using single-note Patches
like sax and flute.
1. Make sure that the PATCH PLAY display is showing.
2. Press [SOLO] so its indicator lights.
Now you can play a solo.
* This setting is linked with the Assign parameter (PATCH/
CONTROL/KEY MODE & BENDER). When the [SOLO]
indicator is turned on, the Assign parameter will be set to
SOLO. When the indicator is dark, it will be set to POLY.
3. Play the XP-30 keyboard.
* If you press [SOLO] when Single Performance is selected, the
Solo function can be switched on or off for the current Part.
When Layer Performance is selected, the Solo function can be
switched on or off for the Parts with the Local parameter
(PERFORM/MIDI/MIDI) set ON. If a Rhythm Set is selected,
[SOLO] cannot be turned on.
■ Creating Smooth Pitch Changes
(Portamento)
Portamento ensures a smooth pitch changeover from one
note to the next note played. When [SOLO] is on (indicator
lights), you can simulate techniques like violin glissandos.
1. Make sure that the PATCH PLAY display is showing.
2. Press [PORTAMENTO]. Its indicator lights.
You’re ready to play portamento.
* This setting is linked with the Sw parameter (PATCH/
CONTROL/PORTAMENTO).
3. To change the portamento settings, press [EDIT] to make
the indicator light. Then press the [CONTROL] function
button, and press [ ] or [ ] to access the
PORTAMENTO display.
fig.2-06
4. Move the cursor over to Time, Mode, Type or Start
parameter.
See p. 73 for each parameter’s functions.
5. Rotate the VALUE dial or press [INC]/[DEC] to get the
value you want.
6. Press [EXIT] to return to the PATCH PLAY display and
play.
* If you press [PORTAMENTO] when Single Performance is
selected, the Portamento function can be switched on or off for
the current Part. When Layer Performance is selected, the
Portamento function can be switched on or off for the Parts with
the Local parameter (PERFORM/MIDI/MIDI) set ON. If a
Rhythm Set is selected, [PORTAMENTO] cannot be turned on.
■ Using the Sliders to Modify the
Sound in Realtime
(Sound Palette Function)
With the four sliders in the PALETTE section, you can create
sound variations or volume changes in real time.
* Sound variations or volume changes made with the Sound
Palette affect only the performance. They have no effect on
current Patch settings. Change the Patch and these Sound
Palette settings will be lost.
* The sound character and volume changes created using the
Sound Palette will also be transmitted to the external MIDI
devices.
- OWNER’S MANUAL 1
- IMPORTANT SAFETY INSTRUCTIONS 2
- SAVE THESE INSTRUCTIONS 2
- USING THE UNIT SAFELY 4
- Important Notes 5
- Contents 10
- Main Features 11
- Front and Rear Panel 12
- ■ Rear Panel 14
- Quick Start 15
- Getting Ready 16
- “Turning On the Power” (p 18
- “Turning Off 19
- Outil d'installation 22
- “Turning 23
- Off the Power” (p. 26) et 23
- Making Connections 24
- “Connecting to Your 25
- Computer” (p. 134) 25
- Turning On the Power 26
- (Factory Reset) 27
- Listening to the Demo Song 28
- ■ Profile of the Composer 29
- Playing the Sounds 30
- (Patch Search Function) 32
- Try Out Performance Functions 34
- ■ Hold Pedal 35
- ■ Expression Pedal 35
- ■ Portamento 35
- 516 2,4,5,7 36
- Advanced Use 39
- XP-30 Configuration 40
- Performance 41
- Basic Operation 42
- ■ About the Function Buttons 43
- ■ About the Cursor Buttons 44
- ■ Modifying a Value 45
- ■ Assigning a Name 46
- Chapter 2. Playing 47
- Chapter 2 49
- Playing in Performance Mode 51
- ■ Playing Along with a Song 53
- Playback (XP-30 Used as a 53
- Multitimbral Sound Source) 53
- Sound in Realtime 54
- (Sound Palette Function) 54
- Playing in Rhythm Set Mode 55
- Playing an Arpeggio 56
- ■ Playing an Arpeggio Over a 57
- Preset Keyboard Area 57
- Using a Hold Pedal 58
- Convenient Functions for 59
- Semitone Steps (Transpose) 60
- Note Does Not Sound (Panic) 60
- Regarding Effects 61
- Sound Editing Procedures 62
- Note on Tone Editing 64
- ■ Editing a Performance 65
- ■ Editing a Rhythm Set 66
- Keeping Edited Sound 67
- Functions of Patch Parameters 68
- VELOCITY (Velocity Range) 69
- KEY RANG (Key Range) 70
- STRUCT (Structure) 70
- (EFFECTS) 71
- PATCH CHORUS 72
- Sounds Are Played (CONTROL) 73
- RxSWITCH (Receive Switch) 74
- PEAK & HOLD 74
- CONTROL SOURCE 75
- CONTROL 1–3 75
- ■ Modifying Waveform (WAVE) 76
- ■ Modulating Sounds (LFO) 78
- ■ Modifying Pitch (PITCH) 79
- Frequency 80
- T1 T2 T3 T4 81
- LOWER&UPPER 82
- LOWER UPPER 82
- Functions of Performance 83
- Parameters 83
- ■ Setting Effects for a 84
- Performance (EFFECTS) 84
- PERFORM CHORUS 85
- PERFORM REVERB 85
- ■ Controlling How a Rhythm 90
- Tone will Sound with 90
- Controllers (CONTROL) 90
- ■ Modifying Waveform of a 90
- Rhythm Tone (WAVE) 90
- ■ Changing the Volume and 92
- Stereo Location of a Rhythm 92
- Tone (TVA) 92
- Multi-Effects Types 93
- (EFX Parameter) 93
- 4: PHASER 94
- 5: SPECTRUM 94
- 6: ENHANCER 94
- 7: AUTO-WAH 95
- 8: ROTARY 95
- 9: COMPRESSOR 96
- 10: LIMITER 96
- 11: HEXA-CHORUS 96
- 15: STEREO-FLANGER 98
- 16: STEP-FLANGER 98
- 17: STEREO-DELAY 99
- 18: MODULATION-DELAY 99
- 19: TRIPLE-TAP-DELAY 100
- Chapter 3 101
- 20: QUADRUPLE-TAP-DELAY 101
- 21: TIME-CONTROL-DELAY 101
- 22: 2VOICE-PITCH-SHIFTER 102
- 23: FBK-PITCH-SHIFTER 102
- (Feedback Pitch Shifter) 102
- 27: OVERDRIVE→FLANGER 104
- 28: OVERDRIVE→DELAY 104
- 29: DISTORTION→CHORUS 104
- 34: ENHANCER→DELAY 106
- 35: CHORUS→DELAY 106
- 36: FLANGER→DELAY 106
- XP-30 Operating Environment 108
- Setup (System Parameters 108
- ■ Keyboard and Controllers 110
- Settings (CONTROL) 110
- ■ MIDI Settings (MIDI) 112
- ■ Phrase Preview Settings 113
- (PREVIEW) 113
- ■ Adjusting Tuning (TUNE) 113
- ■ Program Change (PGM CHNG) 114
- Installation Status of Wave 114
- Expansion Boards (INFO) 114
- About Utility/Card Mode 115
- Basic Procedure in Utility/ 115
- Card Mode 115
- Storing Sound Data in User 116
- Memory (WRITE) 116
- Copying Sound Source 117
- Settings (COPY) 117
- ■ Rhythm Set Copy 118
- Initializing Sound Source 119
- Settings (INIT) 119
- Transmitting Sound Settings 119
- ■ Transmitting Data to User 120
- Preventing User Memory 121
- Writing Operation (PROTECT) 121
- Memory Card-Related 121
- Settings (CARD) 121
- Loading a File from Memory 122
- Card into the XP-30 (LOAD) 122
- Saving Data to Memory Card 122
- Recalling Factory Default 123
- Settings (FACTORY RESET) 123
- Entering GM Mode 124
- Modifying GM Mode Settings 125
- GM CHORUS 126
- GM REVERB 126
- Convenient Functions in GM 127
- Mode (GM Utility) 127
- ■ Initializing GM Mode (INIT) 128
- Techniques for Using Patches 129
- Using the XP-30 to Play Live 131
- Using External MIDI Devices 132
- Chapter 6 133
- Selecting Patches 133
- Selecting Performances 133
- Selecting Rhythm Sets 133
- Apple Macintosh 134
- ■ Disconnecting the Keyboard 137
- (Local OFF) 137
- Appendices 139
- Troubleshooting 140
- Error Messages 142
- Quick Reference of Procedures 143
- ■ Controller Settings 144
- ■ Saving and Loading Data 145
- ■ Controlling External MIDI 145
- External MIDI Device 146
- Parameter List 147
- CONTROL Group (p. 73) 148
- WAVE Group (p. 76) 148
- LFO Group (p. 78) 148
- ■ Performance Parameters 150
- ■ Rhythm Set Parameters 151
- ■ GM Mode Parameters 153
- ■ EFX Parameters 154
- ■ System Parameters 158
- Waveform List 160
- INT-B (Internal B) 161
- ● XP-A Menu Waveforms 163
- ● XP-C Menu Waveforms 166
- Patch List 168
- ■ B.P.M. CONVERSION TABLE 174
- Rhythm Set List 177
- Performance List 181
- Arpeggio Style List 182
- MIDI Implementation 183
- 3. Parameter Address Map 190
- 4. Supplementary Material 199
- 10 02 00 00H 204
- 00 00H Patch Common 204
- MIDI Implementation Chart 206
- Specifications 207
- For PC (25-pin) 208
- Apparatus containing 215
- Lithium batteries 215
- Information 216
Related products and manuals for Digital pianos Roland XP-60
Digital pianos Roland DP-990F Owner's Manual
(108 pages)
(108 pages)
Digital pianos Roland VR-760 Owner's Manual
(120 pages)
(120 pages)
Digital pianos Roland UM-ONE User Manual
(2 pages)
(2 pages)
Digital pianos Roland MT-90U Owner's Manual
(72 pages)
(72 pages)
Digital pianos Roland BK-9 User Manual
(12 pages)
(12 pages)
Digital pianos Roland SYB-5 User Manual
(28 pages)
(28 pages)
Digital pianos Roland Fantom XR Owner's Manual
(284 pages)
(284 pages)
Digital pianos Roland BK-9 User's Guide
(22 pages)
(22 pages)
Digital pianos Roland E-600 User Manual
(4 pages)
(4 pages)
Digital pianos Roland SH-2 User Manual
(10 pages)
(10 pages)
Digital pianos Roland PK-7A Owner's Manual
(13 pages)
(13 pages)
Digital pianos Roland RD-300GX User Manual
(114 pages)
(114 pages)
Digital pianos Roland UM-ONE User Manual
(2 pages)
(2 pages)
Digital pianos Roland MP-60 User Manual
(1 pages)
(1 pages)
Digital pianos Roland A-88 User Manual
(24 pages)
Digital pianos Roland VK-88 Owner's Manual
(112 pages)
(112 pages)
© 2020, manymanuals.com. All rights reserved. | 0.406 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals