Roland VS-2000 User's Guide download pdf (Page 259)

259

Chapter 22 Specific Applications

Chapter 22

Hold [SHIFT] and press [EXT SYNC]. The Sync/Tempo

screen appears in the display.

Use [ ], [ ], [ ], and [ ] to move the

cursor and use the TIME/VALUE dial to change the

settings.

Sync Error Level

Normally, this is set to “5.” If you are having difficulties,

setting a longer interval allows synchronization to

continue even if there are errors in the source MTC.

Sync MTC Type

This selects the MTC frame rate (30, 29N, 29D, 25,24).

Select the MTC rate so it matches the rate of the SI-80S

(30, 29D or 29N).

Press [PLAY (DISPLAY)] to return to the Playlist display.

Press [EXT SYNC]. The button indicator lights,

indicating the VS-1680 is synchronized using MTC

received from the SI-80S. In this state, commands such as

Play and Stop performed on the video equipment are

also performed on the VS-1680.

Using External Effects Units

When using external effects devices, the AUX A/B jacks

serve as effects send jacks. The following example describes

how effects can be added to a stereo recording on Track 9/10.

Follow these steps when you want to use an external effects

unit. Use the INPUT 7 and 8 jacks as the effect return jacks.

Connect your effects unit as shown here:

fig.13-06

Press Track 9/10 SELECT. The Track Mixer appears in

the display.

Press [F5 (AUX)]. If “AUX” does not appear in the

display above [F5], press [PAGE] until you see “AUX,”

and then press [F5 (AUX)].

* If EFFECT B is not installed in the VS-1680, [F4] displays

“AUX3.”

Turn the TIME/VALUE dial to select “Pst.”

Press [ ] to move the cursor and adjust AUX level (0-

127) and pan (L63-R63) as needed.

Press [MASTER]. The Master Block appears in the

display.

Press [F3 (AUX.A)]. If “AUX.A” does not appear in the

display above [F3], press [PAGE] until you see “AUX.A,”

and then press [F3 (AUX.A)].

Turn the TIME/VALUE dial to select “AUX.”

Press [ST IN].

10.

Use the TIME/VALUE to select “Input 7/8” for StereoIn

Select.

11.

Press [ ] and [ ] to move the cursor. Adjust the

volume level (0-127) and pan (L63-R63) as needed.

12.

If you are using an effect that you want to add to the

original signal—such as a reverb or delay—proceed to

Step 13.

If you want the effect to replace the original signal—such

as when you are using a mic preamp or compressor—

press Track 9/10 SELECT and turn the Mix parameter to

“Off” so that only the effect is heard.

13.

Press [PLAY (DISPLAY)] to return to the Playlist display.

You are now ready to use the external effect unit.

14.

While playing back the song, adjust the sound of the

effect. To control the external effect return level using the

channel fader on the VS-1680, press [FADER/MUTE] so

“IN” is lit. Then use the “ST IN” fader (same as Track

Fader 11/12) to adjust external effect return level. When

you are satisfied with the level, press [FADER/MUTE]

so “TR” is lit.

INPUT OUTPUT

1 2 ... 254 255 256 257 258 259 260 261 262 263 264 ... 281 282

Comments to this Manuals

No comments

Roland VS-2000 User's Guide Page 259

Comments to this Manuals

Related products and manuals for Musical Instruments Roland VS-2000