Roland VS-300 User Manual Page 110
- Page / 122
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Chapter 5 What to Do If
108
5-6 If a Message Appears
These are the main messages that appear on the
machine's display to prompt correct operation. They
do not indicate any error. Follow the prompts and
take action accordingly.
[CLOSE THE COVER]
Close the front cover and the left and right side covers. For
safety, the carriage doe not operate while a cover is open.
[SHEET NOT LOADED SETUP SHEET]
Load media. This message appears when an attempt to per-
form a printing test was made while no media was loaded.
[1■ 2■ 3■ 4■]
Only a small amount of ink remains. Replace the cartridge
indicated by the flashing number with a new cartridge.
[EMPTY DRAIN BOTTLE]
Detach the drain bottle from the machine, discard the dis-
charged fluid, then reinstall the drain bottle on the machine.
Press
to continue. This message appears before
operations that discharge a large amount of ink.
[INSTALL DRAIN BOTTLE]
Check whether the drain bottle is installed. Install the drain
bottle, then press
.
[TIME FOR MAINTENANCE]
It is time to clean the heads using the cleaning kit. After
verifying, press
.
☞
p 46 "Cleaning the Heads Using the Cleaning Kit"
[TIME FOR WIPER REPLACE]
It is time to replace the wiper. After verifying, press .
☞
p 51 "Replacing the Wipers"
[TIME FOR SPONGE REPLACE]
It is time to replace the ink-absorbing material. After re-
placing, press
.
☞
p 54 "Replacing the Ink-Absorbing Material"
[PRESS THE POWER KEY TO CLEAN]
If you're using ECO-SOL INK, this appears when the ma-
chine has been unused for about one month.
This feature is to remind you to switch on the sub power
once a month. When the machine remains unused for about
one month, this screen appears and a warning beep sounds.
If this screen appears, switch on the sub power. When main-
tenance operations finish, switch off the sub power.
This feature operates when the printer's main power is turned
on. We recommend leaving on just the main power to the
printer even when the machine is to remain out of use for a
prolonged period.
☞
p 59 "When Not in Use for a Prolonged Period"
Downloaded From ManualsPrinter.com Manuals
- USER'S MANUAL 1
- Table of Contents 3
- To Ensure Safe Use 6
- Warning Labels 10
- Avis sur les avertissements 11
- ATTENTION 11
- PRUDENCE 11
- À propos des symboles 11
- Intérieur de le couvercle 12
- La cartouche d'encre 12
- Printer unit 17
- Ink cartridges 18
- Chapter 1 19
- Introduction 19
- 1-1 Machine Features 20
- 1-2 Part Names and Functions 21
- Chapter 1 Introduction 22
- Operation Panel 23
- Chapter 2 25
- Operation 25
- Chapter 2 Operation 26
- The Power-saving Feature 27
- How to Load Roll Media 28
- Align the media 29
- Pull out the media 30
- Set the media clamps 31
- Close the front cover 31
- Ye s N o 32
- How to Cut Off Media 33
- Temperature Settings 34
- General Guide for Adjustment 35
- 2-4 Starting Output 36
- Printing Test and Cleaning 37
- 2-5 If Ink Runs Out 38
- If Ink Runs Out 39
- 2-6 Performing Cutting 40
- Performing a Cutting Test 41
- Chapter 3 43
- Maintenance and 43
- Adjustment 43
- Disposing of Discharged Ink 44
- Cleaning 45
- Daily Care and Maintenance 46
- Periodic Care and Maintenance 46
- Start cleaning 47
- How to Perform Cleaning 48
- Remove the side cover 50
- CLOSE MAINTE 52
- NANCE COVER 52
- Replacing the Wipers 53
- Remove the stopper 55
- Attach the side cover 55
- Press 55
- Procedure 56
- Replacing the Blade 58
- Reinstall the blade holder 59
- Tighten the screw 59
- Keep Performing Maintenance 61
- Chapter 4 63
- Feature Reference 63
- Description 64
- Print a test pattern 66
- Enter the correction value 69
- Default Setting 70
- Using Transparent Media 72
- Printing Hard-to-dry Media 72
- How to Load Sheet Media 76
- Deactivating the Sleep Mode 78
- [FEED FOR DRY] : ENABLE 80
- Printing with Crop Marks 83
- CROPMARK ERROR 84
- NOT FOUND 84
- Aligning Manually and Cutting 85
- About Align Points 86
- A B C 88
- [FEED SETTING] : 0.0 mm 92
- [SCAN SETTING] : 0.0 mm 92
- 4-9 Performing Maintenance 93
- Printing a System Report 94
- 4-11 Menu List 100
- Chapter 4 Feature Reference 100
- Language and Unit Menu 101
- Cutting Configuration Menu 101
- Cleaning and Maintenance Menu 101
- Heater Configuration Menu 102
- What to Do If 103
- Chapter 5 103
- Chapter 5 What to Do If 104
- W 500mm 104
- 1 2 3 4 104
- 5-3 The Media Jams 107
- Media Wrinkles or Shrinks 108
- The Media Is Not Straight 108
- Media Feed Is Not Smooth 108
- What to Do First 109
- 5-6 If a Message Appears 110
- Chapter 6 113
- Specifications 113
- 6-1 Usable Media 114
- 6-2 Printing/Cutting Area 115
- Chapter 6 Specifications 116
- 6-3 About the Blade 117
- 6-5 Specifications 119
- R4-081106 122
Related products and manuals for Print & Scan Roland VS-300
Print & Scan Roland AJ-1000 Setup Guide
(36 pages)
(36 pages)
Print & Scan Roland SJ-740 User Manual
(102 pages)
(102 pages)
Print & Scan Roland VS-540 User Manual
(6 pages)
(6 pages)
Print & Scan Roland SJ-600 User Manual
(116 pages)
(116 pages)
Print & Scan Roland VS-640i User Manual
(176 pages)
(176 pages)
Print & Scan Roland XR-640 User Manual
(80 pages)
(80 pages)
Print & Scan Roland PC-600 User Manual
(56 pages)
(56 pages)
Print & Scan Roland PNC-950 User Manual
(41 pages)
(41 pages)
Print & Scan Roland XR-640 User Manual
(4 pages)
(4 pages)
Print & Scan Roland LEC-540 Setup Guide
(64 pages)
(64 pages)
Print & Scan Roland LEC-540 User Manual
(2 pages)
(2 pages)
Print & Scan Roland RA-640 Specifications
(36 pages)
(36 pages)
Print & Scan Roland FJ-52 User Manual
(78 pages)
(78 pages)
Print & Scan Roland VS-640i User Manual
(9 pages)
(9 pages)
Print & Scan Roland LEC-300 Specifications
(56 pages)
(56 pages)
Print & Scan Roland CX-400 Specifications
(64 pages)
(64 pages)
Print & Scan Roland CX-400 User Manual
(24 pages)
(24 pages)
© 2020, manymanuals.com. All rights reserved. | 0.060 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals