Roland XP-80 Owner's Manual Page 77
- Page / 244
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Phase
Adjust the spatial spread of the sound.
Filter Type
Select the type of filter.
OFF
: a filter will not be used
LPF
: cut the frequency range above the cutoff frequency
HPF
: cut the frequency range below the cutoff frequency
Cutoff Freq(Cutoff frequency)
Adjust the basic frequency of the filter.
Low Gain
Adjust the gain of the low frequency range.
High Gain
Adjust the gain of the high frequency range.
Balance (Effect balance)
Adjust the volume balance between the direct sound and the
processed sound.
Level (Output level)
Adjust the output level.
16: STEP-FLANGER
The Step Flanger effect is a flanger in which the flanger pitch
changes in steps. The speed at which the pitch changes can
also be specified in terms of a note-value of a specified
tempo.
Pre Delay (Pre delay time)
Adjust the time delay from when the direct sound begins
until the processed sound is heard.
Rate
Adjust the rate of modulation.
Depth
Adjust the depth of modulation.
Feedback (Feedback level) #
Adjust the amount (%) of the processed sound that is
returned (fed back) into the input. Negative (-) settings will
invert the phase.
Phase
Adjust the spatial spread of the sound.
Step Rate #
Adjust the rate (period) of pitch change. This parameter can
be set as a note-value of a specified tempo. In this case, spec-
ify the value of the desired note.
As the specified tempo, you may use either the Patch Tempo
parameter (PATCH/Common/General), Performance
Tempo (PERFORM/Common/Common), or the tempo
clock of the XP-80’s sequencer.
If you want to use a fixed tempo in Patch mode (Patch
Tempo parameter setting), set the Clock Source parameter
(PATCH/Common/Common General) to PATCH and set
the desired tempo.
If you want to use the sequencer’s tempo clock in Patch
mode, set the Clock Source parameter (PATCH/Common/
Common General) to SEQUENCER.
If you want to use a fixed tempo in Performance mode
(Perform Tempo parameter setting), set the Clock Source
parameter (PERFORM/Common/Common) to PERFORM
and set the desired tempo.
If you want to use the sequencer’s tempo clock in
Performance mode, set the Clock Source parameter (PER-
FORM/Common/Common) to SEQUENCER.
Low Gain
Adjust the gain of the low frequency range.
High Gain
Adjust the gain of the high frequency range.
Balance (Effect balance)
Adjust the volume balance between the direct sound and the
processed sound.
Level (Output level)
Adjust the output level.
17: STEREO-DELAY
This is a stereo delay.
When Feedback Mode parameter is NORMAL:
When Feedback Mode parameter is CROSS:
Delay Left (Delay time left)
Adjust the time from the original sound until when the left
delay sound is heard.
L
R
EQ
Flanger
Flanger
EQ
L
R
Delay
Delay
EQ
EQ
L
R
Delay
Delay
EQ
EQ
79
Chapter 3. Creating your own sounds
- USING THE UNIT SAFELY 1
- Important notes 2
- Before Using Floppy Disks 3
- Usinng The Printed Circuit 3
- Features of the XP-80 4
- Chapter outlines 5
- Contents 6
- Front panel 12
- I. SEQUENCER section 13
- Side panel 14
- Rear panel 15
- XP-80 configuration 16
- Performances 17
- Rhythm Sets 17
- Basic operation 18
- Moving the cursor 21
- Modifying a value 21
- Assigning a name 22
- Chapter 2. Playing 24
- Displaying a Patch list 25
- (turning a Tone on/off) 25
- Changing sound characters 26
- Playing in Performance mode 27
- (Sound Palette) 30
- Playing in Rhythm Set mode 31
- Rhythm Set 32
- Playing an arpeggio 33
- Recording an arpeggio 35
- (Octave Shift) 35
- Regarding effects 37
- Sound editing procedures 38
- Editing a Performance 41
- Editing a Rhythm Set 42
- Keeping edited sound 43
- Functions of Patch parameters 44
- Common Control display 45
- Structure display 47
- Pitch display 50
- Pitch Envelope display 51
- TVF Envelope display 52
- TVA Envelope display 54
- Time 1 Time 2 Time 3 Time 4 54
- Control Switch display 57
- EFX Type name 58
- Chorus display 62
- Reverb display 62
- Common display 63
- Lower Upper 64
- Key range specified for Patch 64
- [PERFORM] 65
- [F4] (MIDI) 65
- [F5] (Effects) 66
- Part Information display 67
- Frequency 69
- Time 1 Time 2 70
- Time 3 Time 4 70
- [RHYTHM] 71
- [F5] (Key Ctl) 71
- 2: OVERDRIVE 72
- 3: DISTORTION 72
- 4: PHASER 73
- 5: SPECTRUM 73
- 6: ENHANCER 73
- 7: AUTO-WAH 74
- 8: ROTARY 74
- 9: COMPRESSOR 74
- 10: LIMITER 75
- 11: HEXA-CHORUS 75
- 12: TREMOLO-CHORUS 75
- 13: SPACE-D 76
- 14: STEREO-CHORUS 76
- 15: STEREO-FLANGER 76
- 16: STEP-FLANGER 77
- 17: STEREO-DELAY 77
- 18: MODULATION-DELAY 78
- 19: TRIPLE-TAP-DELAY 79
- 20: QUADRUPLE-TAP-DELAY 79
- 21: TIME-CONTROL-DELAY 80
- 22: 2VOICE-PITCH-SHIFTER 80
- 24: REVERB 81
- 38: CHORUS/DELAY 86
- 39: FLANGER/DELAY 86
- 40: CHORUS/FLANGER 86
- Setup display 86
- Adjusting tuning (Tune) 87
- [SYSTEM] 87
- [F2] (Tune) 87
- MIDI settings (MIDI) 88
- [F3] (MIDI) 88
- Control Assign display 90
- Pedal Assign display 90
- Arpeggio settings (Arpeg) 91
- [F5] (Arpeg) 91
- System Information display 93
- About the sequencer 94
- Playing back a song 95
- (Quick Play) 96
- Reserve 1 97
- Reserve 2 97
- Reserve 3 97
- Playing back a Pattern 99
- Before you start to record 102
- Selecting instrument sounds 103
- Setting the time signature 103
- Performing realtime recording 106
- (Realtime Erase) 108
- Recording tempo changes 108
- Canceling recording (Undo) 110
- (Step recording) 111
- Inputting data step by step 111
- Inputting chords 112
- Inputting ties 112
- Inputting a dotted note 112
- Inputting rests 112
- Erasing wrong notes 112
- Deleting recording (Undo) 113
- Saving only a song 114
- Chapter 5. Editing a song 115
- Settings for an entire song 116
- Locate function 117
- Setting loop 118
- [SEQUENCER]➞[F5] (Loop) 118
- Editing performance data over 119
- Setting the editing area 120
- [SEQUENCER]➞[F3] (TrkEdit) 120
- Copying a phrase – 3 Copy 122
- (Insert measure) 124
- (Change velocity) 125
- (Change MIDI channel) 126
- (Change gate time) 127
- Aligning a song’s timing 134
- (Quantize) 134
- Grid quantize 135
- Shuffle quantize 136
- Groove quantize 137
- [SEQUENCER]➞[F4] (Micro) 142
- Phrase track/Pattern 144
- Erasing performance data 147
- Moving performance data 147
- Copying performance data 147
- Getting ready to use RPS 148
- Playing using RPS 149
- Getting ready for Chain Play 151
- Saving a chain to disk 152
- Chain play 152
- About Utility mode 153
- Performance write 154
- Patch write 154
- Rhythm Set write 154
- [UTILITY]➞[1]➞[ENTER] 154
- Performance copy 155
- [UTILITY]➞[2]➞[ENTER] 155
- Patch copy 156
- Rhythm Set copy 157
- – 3 Initialize 158
- 4 Data Transfer 159
- [UTILITY]➞[4]➞[ENTER] 160
- [UTILITY]➞[5]/[6]/[7]➞[ENTER] 162
- – 8 Factory (Factory preset) 163
- About Disk mode 164
- XP-80 – 1 Load 165
- Saving data to disk – 2 Save 166
- – 3 Format 167
- 5 Verify 168
- Changing the name of disk – 168
- Deleting unwanted files – 169
- 7 Delete (Delete file) 169
- Renaming a file – 8 Rename 169
- 9 Info (Disk information) 170
- Entering GM mode 171
- Modifying GM mode settings 172
- [SHIFT]+[PERFORM]➞[F6] (Info) 173
- Convenient functions in GM 174
- Transfer (GM Data Transfer) 175
- Techniques for using Patches 176
- Using the XP-80 to play live 177
- OUTPUTLEVEL 178
- CLICK OUT 178
- Changing the Patch 179
- Changing the Performance 179
- Changing the Rhythm Set 179
- Using external MIDI devices 180
- Synchronization with external 181
- MIDI devices 181
- Disk Recorder 182
- MIDI OUT 183
- MIDI OUTMIDI IN 183
- Recording on the XP-80 184
- Troubleshooting 185
- Error messages 186
- Parameter List 188
- WG Group 189
- TVF Group 189
- TVA Group 190
- LFO&Ctl Group 190
- Effects Group 191
- Performance Parameters 192
- Rhythm Set Parameters 193
- Key TVF Group 194
- Key TVA Group 194
- Key Ctl Group 194
- GM Parameters 195
- Info Group 196
- EFX Parameters 197
- System Parameters 202
- Control Group 203
- Arpeg Group 203
- Factory Preset Settings 204
- INT-B (Internal B) 205
- Patch List 206
- GM (GM Group) 208
- Rhythm set List 209
- Performance List 210
- Arpeggio style list 211
- MIDI implementation 212
- ■ Channel Mode messages 214
- ■ System Realtime messages 215
- ■ System Exclusive messages 215
- ■ Channel Voice messages 216
- ■ Channel voice messages 217
- 1-1-1.System Common 220
- 1-1-2.Scale Tune 220
- 1-2.Performance 220
- 1-2-1.Performance Common 221
- 1-2-2.Performance Part 221
- 1-3.Patch 221
- 1-3-1.Patch Common 221
- 1-3-2.Patch Tone 222
- 1-4.Rhythm Setup 223
- 1-4-1.Rhythm Common 223
- 1-4-2.Rhythm Note 223
- 6. Supplementary material 224
- Thus, the address is: 225
- 00 00H Patch Common 226
- MIDI Implementation Chart 227
- Specifications 229
- Quick reference of displays 230
- Performance mode [PERFORM] 231
- Rhythm Set mode [RHYTHM] 232
- GM mode [SHIFT] + [PERFORM] 233
- Sequencer mode [SEQUENCER] 234
- Chain Play mode [CHAIN PLAY] 236
- System mode [SYSTEM] 236
- Utility mode [UTILITY] 237
- Disk mode [DISK] 238
- Information 244
Related products and manuals for Musical Instruments Roland XP-80
Musical Instruments Roland HP508 User Manual
(40 pages)
Musical Instruments Roland RD-700GX User Manual
(149 pages)
(149 pages)
Musical Instruments Roland AT-30 User Manual
(51 pages)
(51 pages)
Musical Instruments Roland SD-90 Owner's Manual
(161 pages)
(161 pages)
Musical Instruments Roland XP-80 User Manual
(39 pages)
(39 pages)
Musical Instruments Roland VG-88 User Manual
(72 pages)
(72 pages)
Musical Instruments Roland FP-9 User Manual
(41 pages)
(41 pages)
Musical Instruments Roland FP-7 User Manual
(184 pages)
(184 pages)
Musical Instruments Roland BR-900CD User Manual
(229 pages)
(229 pages)
Musical Instruments Roland VS-2000 User's Guide
(282 pages)
(282 pages)
Musical Instruments Roland DR-3 User Manual
(121 pages)
(121 pages)
© 2020, manymanuals.com. All rights reserved. | 0.077 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals