Roland Fantom-S Owner's Manual download pdf (Page 21)

Effects List

06: STEP FILTER

This is a filter whose cutoff frequency can be modulated in steps.

You can specify the pattern by which the cutoff frequency will

change.

fig.MFX-06

07: ENHANCER

Controls the overtone structure of the high frequencies, adding

sparkle and tightness to the sound.

fig.MFX-07

08: AUTO WAH

Cyclically controls a filter to create cyclic change in timbre.

fig.MFX-08

Filter Slope

-12, -24, -36 dB Amount of attenuation per octave

-36 dB:

extremely steep

-24 dB:

steep

-12 dB:

gentle

Filter

Cutoff #

0–127 Cutoff frequency of the filter

Increasing this value will raise the

cutoff frequency.

Filter

Resonance #

0–127 Filter resonance level

Increasing this value will emphasize

the region near the cutoff frequency.

Filter Gain 0– +12 dB Amount of boost for the filter output

Modulation

OFF,ON On/off switch for cyclic change

Modulation

Wave

TRI, SQR,

SIN, SAW1,

SAW2

How the cutoff frequency will be mod-

ulated

TRI:

triangle wave

SQR:

square wave

SIN:

sine wave

SAW1:

sawtooth wave (upward)

SAW2:

sawtooth wave (downward)

Rate # 0.05–10.00 Hz,

note

Rate of modulation

Depth 0–127 Depth of modulation

Attack # 0–127 Speed at which the cutoff frequency

will change

This is effective if Modulation Wave

is SQR, SAW1, or SAW2.

Level 0–127 Output level

Parameter

Value Description

Step 01–16

0–127 Cutoff frequency at each step

Rate # 0.05–10.00 Hz,

note

Rate of modulation

Attack # 0–127 Speed at which the cutoff frequency

changes between steps

Filter Type LPF, BPF,

HPF, NOTCH

Filter type

Frequency range that will pass

through each filter

LPF:

frequencies below the cutoff

BPF:

frequencies in the region of the

cutoff

HPF:

frequencies above the cutoff

NOTCH:

frequencies other than the

region of the cutoff

Filter Slope -12, -24, -36 dB Amount of attenuation per octave

-12 dB:

gentle

-24 dB:

steep

-36 dB:

extremely steep

Filter

Resonance #

0–127 Filter resonance level

Increasing this value will emphasize

the region near the cutoff frequency.

Filter Gain 0– +12 dB Amount of boost for the filter output

Level 0–127 Output level

Parameter

Value Description

SAW1 SAW2

L in

R in

L out

R out

Step Filter

Parameter

Value Description

Sens #

0–127 Sensitivity of the enhancer

Mix # 0–127 Level of the overtones gen-

erated by the enhancer

Low Gain -15– +15 dB Gain of the low range

High Gain -15– +15 dB Gain of the high range

Level 0–127 Output Level

Parameter

Value Description

Filter Type

LPF, BPF Type of filter

LPF:

The wah effect will be applied

over a wide frequency range.

BPF:

The wah effect will be applied

over a narrow frequency range.

Manual # 0–127 Adjusts the center frequency at which

the effect is applied.

Peak 0–127 Adjusts the amount of the wah effect

that will occur in the range of the center

frequency.

Set a higher value for Q to narrow

the range to be affected.

Sens # 0–127 Adjusts the sensitivity with which the

filter is controlled.

Polarity UP, DOWN Sets the direction in which the frequen-

cy will change when the auto-wah filter

is modulated.

UP:

The filter will change toward a

higher frequency.

DOWN:

The filter will change to-

ward a lower frequency.

Rate # 0.05–10.00 Hz,

note

Frequency of modulation

Depth # 0–127 Depth of modulation

Phase # 0–180 deg Adjusts the degree of phase shift of the

left and right sounds when the wah ef-

fect is applied.

Low Gain -15– +15 dB Gain of the low range

High Gain -15– +15 dB Gain of the high range

Level 0–127 Output Level

L in

R in

L out

R out

Mix

Enhancer

2-Band

L in

R in

L out

R out

Auto Wah

2-Band EQ

Auto Wah

List_e 21 ページ２００３年５月１５日　木曜日　午後１時３５分

1 ... 20 21 22 ... 80

Comments to this Manuals

No comments

Roland Fantom-S Owner's Manual Page 21

Comments to this Manuals

Related products and manuals for Keyboards Roland Fantom-S