34
Effects List
52: 3D DELAY
This applies a 3D effect to the delay sound. The delay sound will be
positioned 90 degrees left and 90 degrees right.
fig.MFX-52
53: TIME CTRL DELAY
A stereo delay in which the delay time can be varied smoothly.
fig.MFX-53
54: LONG TIME CTRL DELAY
A delay in which the delay time can be varied smoothly, and
allowing an extended delay to be produced.
fig.MFX-54
55: TAPE ECHO
A virtual tape echo that produces a realistic tape delay sound. This
simulates the tape echo section of a Roland RE-201 Space Echo.
fig.MFX-55
Level A/B
0–127 Volume of delay A/B
Low Gain -15– +15 dB Gain of the low frequency range
High Gain -15– +15 dB Gain of the high frequency range
Balance # D100:0W–
D0:100W
Volume balance between the direct
sound (D) and the effect sound (W)
Level 0–127 Output level
Parameter
Value Description
Delay Left
0–2600 ms, note Adjusts the delay time from
the direct sound until the de-
lay sound is heard.
Delay Right
Delay Center
Center
Feedback #
-98– +98 % Adjusts the proportion of the
delay sound that is fed back
into the effect. Negative (-)
settings will invert the phase.
HF Damp 200–8000 Hz, BYPASS Adjusts the frequency above
which sound fed back to the
effect will be cut. If you do not
want to cut the high frequen-
cies, set this parameter to BY-
PASS.
Left Level 0–127 Output level of the delay
sound
Right Level
Center Level
Output Mode SPEAKER, PHONES Adjusts the method that will
be used to hear the sound that
is output to the OUTPUT
jacks. The optimal 3D effect
will be achieved if you select
SPEAKER
when using speak-
ers, or
PHONES
when using
headphones.
Low Gain -15– +15 dB Gain of the low range
High Gain -15– +15 dB Gain of the high range
Balance # D100:0W–D0:100W Volume balance between the
direct sound (D) and the effect
sound (W)
Level 0–127 Output Level
Parameter
Value Description
Delay Time # 0–1300 ms, note Adjusts the time until the delay
is heard.
Parameter
Value Description
L
R
3D Delay L
3D Delay R
3D Delay C
Level
Feedback
2-Band
EQ
2-Band
EQ
L out
R out
R in
R out
L in
L out
Feedback
Feedback
Pan L
Pan R
Time Ctrl Delay
Time Ctrl Delay
2-Band EQ
2-Band EQ
Acceleration
0–15 Adjusts the time over which the
Delay Time changes from the
current setting to a specified new
setting.
The rate of change for the Delay
Time directly affects the rate of
pitch change.
Feedback #2 -98– +98 % Adjusts the amount of the delay
that’s fed back into the effect.
Negative (-) settings invert the
phase.
HF Damp 200–8000 Hz,
BYPASS
Adjusts the frequency above
which sound fed back to the ef-
fect is filtered out. If you do not
want to filter out any high fre-
quencies, set this parameter to
BYPASS.
Low Gain -15– +15 dB Gain of the low frequency range
High Gain -15– +15 dB Gain of the high frequency range
Balance # D100:0W–
D0:100W
Volume balance between the di-
rect sound (D) and the delay
sound (W)
Level 0–127 Output level
Parameter
Value Description
Delay Time #
0–2600 ms,
note
Adjusts the time until the delay is heard.
Acceleration 0–15 Adjusts the time over which the Delay
Time changes from the current setting to
a specified new setting.
The rate of change for the Delay Time
directly affects the rate of pitch
change.
Feedback # -98– +98 % Adjusts the amount of the delay that’s
fed back into the effect. Negative (-) set-
tings invert the phase.
HF Damp 200–8000 Hz,
BYPASS
Adjusts the frequency above which
sound fed back to the effect is filtered
out. If you do not want to filter out any
high frequencies, set this parameter to
BYPASS.
Pan # L64–63R Stereo location of the delay
Low Gain -15– +15 dB Gain of the low frequency range
High Gain -15– +15 dB Gain of the high frequency range
Balance # D100:0W–
D0:100W
Volume balance between the direct
sound (D) and the delay sound (W)
Level 0–127 Output level
Parameter
Value Description
L in
R in
L out
R out
2-Band
EQ
Balance W
Balance W
Balance D
Balance D
2-Band
EQ
Feedback
Time Control Delay
Echo Level
Echo Level
L in
R in
L out
R out
Tape Echo
Direct Level
Direct Level
List_e 34 ページ 2003年5月15日 木曜日 午後1時35分
Comments to this Manuals