Roland Fantom-S Owner's Manual download pdf (Page 52)

MIDI Implementation

Status

Data byte Status

F0H 41H, dev, 42H, 12H, aaH, bbH, ccH, F7H

ddH, ... eeH, sum

Byte Explanation

F0H Exclusive status

41H ID number (Roland)

dev Device ID (dev: 10H - 1FH, 7FH)

42H Model ID (GS)

12H Command ID (DT1)

aaH Address MSB: upper byte of the starting address of the transmitted

data

bbH Address: middle byte of the starting address of the transmitted

data

ccH Address LSB: lower byte of the starting address of the transmitted

data

ddH Data: the actual data to be transmitted. Multiple bytes of

data are transmitted starting from the address.

: :

eeH Data

sum Checksum

F7H EOX (End Of Exclusive)

* The amount of data that can be transmitted at one time depends on the type of data, and

data will be transmitted from the specified starting address and size. Refer to the address

and size given in

Parameter Address Map

(p. 58).

* Data larger than 256 bytes will be divided into packets of 256 bytes or less, and each

packet will be sent at an interval of about 20 ms.

* Regarding the checksum, please refer to (p. 76)

* Not received when the Receive Exclusive parameter (SYSTEM/MIDI) is OFF.

2. Data Transmission

■

Channel Voice Messages

●

Note off

Status

2nd byte 3rd byte

8nH kkH vvH

n = MIDI channel number: 0H - FH (ch.1 - 16)

kk = note number: 00H - 7FH (0 - 127)

vv = note off velocity: 00H - 7FH (0 - 127)

●

Note on

Status

2nd byte 3rd byte

9nH kkH vvH

n = MIDI channel number: 0H - FH (ch.1 - 16)

kk = note number: 00H - 7FH (0 - 127)

vv = note on velocity: 01H - 7FH (1 - 127)

●

Polyphonic Key Pressure

Status

2nd byte 3rd byte

AnH kkH vvH

n = MIDI channel number: 0H - FH (ch.1 - 16)

kk = note number: 00H - 7FH (0 - 127)

vv = Polyphonic Key Pressure: 00H - 7FH (0 - 127)

●

Control Change

* By selecting a controller number that corresponds to the setting of parameters of

controllers (REALTIME CONTROL knob, and so on), the Fantom-S/Fantom-S88 can

transmit any control change message.

❍

Bank Select (Controller number 0, 32)

Status

2nd byte 3rd byte

BnH 00H mmH

BnH 20H llH

n = MIDI channel number: 0H - FH (ch.1 - 16)

mm, ll = Bank number: 00 00H - 7F 7FH (bank.1 - bank.16384)

* These messages are transmitted when Patch, Rhythm Set or Performance is selected. But

not transmitted when Transmit Program Change or Transmit Bank Select parameter

(SYSTEM/MIDI) is OFF.

* In Performance mode, these messages are not transmitted when External Bank Select

MSB or External PC Number parameter (PERFORMANCE/PART) is OFF.

* Although with the Fantom-S/Fantom-S88 you can select the Bank Select messages to be

transmitted, be sure to refer to the Program Change Map on (p. 78) for the Bank Select

messages transmitted when the Fantom-S/Fantom-S88 is select a Patch, Rhythm Set or

Performance.

* The Bank Select Numbers corresponding to SRX series should be referred to the SRX

series owner’s manual.

❍

Modulation (Controller number 1)

Status 2nd byte 3rd byte

BnH 01H vvH

n = MIDI channel number: 0H - FH (ch.1 - 16)

vv = Modulation depth: 00H - 7FH (0 - 127)

❍

Breath type (Controller number 2)

Status

2nd byte 3rd byte

BnH 02H vvH

n = MIDI channel number: 0H - FH (ch.1 - 16)

vv = Control value: 00H - 7FH (0 - 127)

❍

Portamento Time (Controller number 5)

Status

2nd byte 3rd byte

BnH 05H vvH

n = MIDI channel number: 0H - FH (ch.1 - 16)

vv = Portamento Time: 00H - 7FH (0 - 127)

❍

Data Entry (Controller number 6, 38)

Status

2nd byte 3rd byte

BnH 06H mmH

BnH 26H llH

n = MIDI channel number: 0H - FH (ch.1 - 16)

mm, ll = the value of the parameter specified by RPN/NRPN

mm = MSB, ll = LSB

List_e 52 ページ２００３年５月１５日　木曜日　午後１時３５分

1 ... 51 52 53 ... 80

Comments to this Manuals

No comments

Roland Fantom-S Owner's Manual Page 52

Comments to this Manuals

Related products and manuals for Keyboards Roland Fantom-S