Roland Fantom-S Owner's Manual download pdf (Page 48)

MIDI Implementation

❍

Portamento control (Controller number 84)

Status

2nd byte 3rd byte

BnH 54H kkH

n = MIDI channel number: 0H - FH (ch.1 - 16)

kk = source note number: 00H - 7FH (0 - 127)

*A Note-on received immediately after a Portamento Control message will change

continuously in pitch, starting from the pitch of the Source Note Number.

* If a voice is already sounding for a note number identical to the Source Note Number,

this voice will continue sounding (i.e., legato) and will, when the next Note-on is

received, smoothly change to the pitch of that Note-on.

* The rate of the pitch change caused by Portamento Control is determined by the

Portamento Time value.

❍

Effect 1 (Reverb Send Level) (Controller number 91)

Status

2nd byte 3rd byte

BnH 5BH vvH

n = MIDI channel number: 0H - FH (ch.1 - 16)

vv = Reverb Send Level: 00H - 7FH (0 - 127)

* In Performance mode the Part Reverb Send Level parameter (PERFORM/PART) will

change.

❍

Effect 3 (Chorus Send Level) (Controller number 93)

Status

2nd byte 3rd byte

BnH 5DH vvH

n = MIDI channel number: 0H - FH (ch.1 - 16)

vv = Chorus Send Level: 00H - 7FH (0 - 127)

* In Performance mode the Part Chorus Send Level parameter (PERFORM/PART) will

change.

❍

RPN MSB/LSB (Controller number 100, 101)

Status

2nd byte 3rd byte

BnH 65H mmH

BnH 64H llH

n = MIDI channel number: 0H - FH (ch.1 - 16)

mm = upper byte (MSB) of parameter number specified by RPN

ll = lower byte (LSB) of parameter number specified by RPN

<<< RPN >>>

Control Changes include RPN (Registered Parameter Numbers), which are extended.

When using RPNs, first RPN (Controller numbers 100 and 101; they can be sent in any

order) should be sent in order to select the parameter, then

Data Entry (Controller numbers 6 and 38) should be sent to set the value. Once RPN

messages are received, Data Entry messages that is received at the same MIDI channel after

that are recognized as changing toward the value of the RPN messages. In order not to

make any mistakes, transmitting RPN Null is recommended after setting parameters you

need.

This device receives the following RPNs.

RPN Data entry

MSB, LSB

MSB, LSB Notes

00H, 00H mmH, llH Pitch Bend Sensitivity

mm: 00H - 18H (0 - 24 semitones)

ll: ignored (processed as 00H)

Up to 2 octave can be specified in semitone steps.

* In Performance mode, the Part Bend Range parameter (PERFORM/PART) will change.

00H, 01H mmH, llH Channel Fine Tuning

mm, ll: 20 00H - 40 00H - 60 00H

(-4096 x 100 / 8192 - 0 - +4096 x 100 / 8192 cent)

* In Performance mode, the Part Fine Tune parameter (PERFORM/PART) will change.

00H, 02H mmH, llH Channel Coarse Tuning

mm: 10H - 40H - 70H (-48 - 0 - +48 semitones)

ll: ignored (processed as 00H)

* In Performance mode, the Part Coarse Tune parameter (PERFORM/PART) will change.

7FH, 7FH ---, --- RPN null

RPN and NRPN will be set as “unspecified.” Once this setting has been made, subsequent

Parameter values that were previously set will not change.

mm, ll: ignored

●

Program Change

Status

2nd byte

CnH ppH

n = MIDI channel number: 0H - FH (ch.1 - 16)

pp = Program number: 00H - 7FH (prog.1 - prog.128)

* Not received in Performance mode when the Receive Program Change parameter

(PERFORM/MIDI) is OFF.

●

Channel Pressure

Status

2nd byte

DnH vvH

n = MIDI channel number: 0H - FH (ch.1 - 16)

vv = Channel Pressure: 00H - 7FH (0 - 127)

* Not received in Performance mode when the Receive Channel Pressure parameter

(PERFORM/MIDI) is OFF.

●

Pitch Bend Change

Status

2nd byte 3rd byte

EnH llH mmH

n = MIDI channel number: 0H - FH (ch.1 - 16)

mm, ll = Pitch Bend value: 00 00H - 40 00H - 7F 7FH (-8192 - 0 - +8191)

* Not received when the Tone Receive Bender parameter (PATCH/GENERAL) is OFF.

* Not received in Performance mode when the Receive Pitch Bend parameter

(PERFORM/MIDI) is OFF.

■

Channel Mode Messages

* Not received in Performance mode when the Receive Switch parameter (PERFORM/

MIDI) is OFF.

●

All Sounds Off (Controller number 120)

Status

2nd byte 3rd byte

BnH 78H 00H

n = MIDI channel number: 0H - FH (ch.1 - 16)

* When this message is received, all notes currently sounding on the corresponding

channel will be turned off.

●

Reset All Controllers (Controller number 121)

Status

2nd byte 3rd byte

BnH 79H 00H

n = MIDI channel number: 0H - FH (ch.1 - 16)

* When this message is received, the following controllers will be set to their reset values.

Controller

Reset value

Pitch Bend Change +/-0 (center)

Polyphonic Key Pressure 0 (off)

Channel Pressure 0 (off)

Modulation 0 (off)

Breath Type 0 (min)

Expression 127 (max)

However the controller will be at minimum.

Hold 1 0 (off)

Sostenuto 0 (off)

Soft 0 (off)

Hold 2 0 (off)

RPN unset; previously set data will not change

NRPN unset; previously set data will not change

List_e 48 ページ２００３年５月１５日　木曜日　午後１時３５分

1 ... 47 48 49 ... 80

Comments to this Manuals

No comments

Roland Fantom-S Owner's Manual Page 48

Comments to this Manuals

Related products and manuals for Keyboards Roland Fantom-S