Roland GT-PRO Owner's Manual Page 129
- Page / 164
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
129
Driver installation and settings (Macintosh)
Installing the driver
Use either OMS or FreeMIDI as the MIDI driver.
The included GT-PRO driver is an add-on module for using the GT-PRO with OMS or
FreeMIDI.
* Either OMS or FreeMIDI must be installed in your Macintosh, as appropriate for the sequencer
software you are using.
Use the following procedure to install the GT-PRO driver.
1
Exit all currently running software (applications).
If you are using a virus checker or similar software, be sure to exit this as well.
2
Prepare the CD-ROM.Insert the CD-ROM into the CD-ROM drive.
3
Double-click the GT-PRO Driver-E Installer icon (found in the Driver E (Mac OS 9) folder of
the CD-ROM) to start up the installer.
4
Verify the Install Location, and click [Install].
fig.12-0210
* If a message like the following is displayed, click [Continue].
The other currently running applications will exit, and installation
will continue.
5
A dialog box will indicate Installation was successful.
Click [Restart] to restart your Macintosh.
Mac OS 9 users
OMS can be found in the OMS 2.3.8 E
folder within the OMS (Mac OS 9)
folder of the CD-ROM.
If you would like to know more about
OMS, refer to OMS_2.3_Mac.pdf
which can be found in the same
folder.
Disconnect the GT-PRO from the Macintosh before you perform the installation.
If a GT-PRO is already connected to your Macintosh when you install the driver, a message
like the following will appear when the Macintosh is started up. Perform the steps described
below as appropriate for the message that is displayed.
If the screen indicates:
“Software needed for the USB device “GT-PRO” is not available. Would you like to
look for the software on the Internet?”
→ click [Cancel].
If the screen indicates:
“The software needed to use the USB device “GT-PRO” cannot be found. Please refer
to the device documentation to install the necessary software”.
→ click [OK].
- Owner’s Manual 1
- USING THE UNIT SAFELY 3
- IMPORTANT NOTES 5
- Contents 7
- Installing & 9
- Main Features 10
- Front Panel 11
- Rear panel 13
- Signal Flow 14
- Chapter 1 Playing Sounds 15
- Turning on the Power 16
- Adjusting the Input Level 17
- Adjusting the Output Level 17
- Turning Off the Power 18
- What is a Patch? 19
- How to Switch Patches 19
- (Patch Change) 19
- Turning the Effect On and Off 20
- Setting the Effects Simply 21
- (QUICK FX) 21
- Changing the Connection 22
- Naming Patches (Patch Name) 23
- Copying Patches (Patch Copy) 24
- Exchanging Patches 25
- (Patch Exchange) 25
- Initializing Patches 25
- Storing Settings by Effect 26
- (User Quick Settings) 26
- Copying the PREAMP/SPEAKER 27
- Settings to Another Channel 27
- PREAMP/SPEAKER (Preamp/ 28
- Speaker Simulator) 28
- Chapter 4 29
- Type List 30
- OVERDRIVE/DISTORTION 31
- OUTPUT L 32
- OUTPUT R 32
- Using the HOLD (Hold Delay) 34
- COMP (Compressor) 35
- FX-1/FX-2 36
- AW (Auto Wah) 38
- TM (Tone Modify) 38
- GS (Guitar Simulator) 38
- FL (Flanger) 40
- VB (Vibrato) 40
- STR (Sitar Simulator) 42
- FB (Feedbacker) 42
- WSY (Wave Synth) 44
- SEQ (Sub Equalizer) 44
- PS (Pitch Shifter) 46
- 2CE (2 x 2 Chorus) 48
- AR (Auto Riff) 48
- AC (Acoustic Processor) 50
- EQ (Equalizer) 51
- (External Effects Loop) 52
- PRE LOOP 53
- AMP CTL (Amp Control) 1/2 54
- FX CHAIN (Effect Chain) 56
- NAME (Patch Name) 56
- Chapter 5 57
- Customizing the Speakers 58
- Customizing 59
- Overdrive/Distortion 59
- Customizing Pedal Wah 60
- Use-Specific Guide 61
- PCS-31PCS-31 62
- Red WhiteRed White 62
- EXP Pedal (EXP1, 2 Function) 63
- Chapter 6 65
- Quick Settings 66
- Target Range 68
- Internal Pedal System 70
- Chapter 7 72
- Transmitting and Receiving 75
- MIDI Data 75
- MIDI Device (Bulk Load) 76
- Changing Patch Numbers on an 78
- About MIDI 79
- About the MIDI implementation 80
- Chapter 8 81
- GT-PRO to the FC-200 82
- Controlling the GT-PRO with 83
- EXP Pedal CC#7 CC#7 Function 84
- Pedal Connected to the 84
- FOOT SW/EXP 1 Jack 84
- CC#1 CC#1 Function 84
- Advanced Settings 86
- Before Connecting with USB 88
- Setting USB-Related Functions 89
- Recording the GT-PRO’s 90
- Output with a Computer 90
- Running the GT-PRO from a 91
- Computer 91
- Adjusting the overall sound 94
- Adjusting the Display 96
- Contrast (LCD Contrast) 96
- Switching the Sounds Input 96
- Switched (Patch Extent) 98
- Setting the Knob Functions 99
- (Knob Mode) 99
- Checking the Effect Level 100
- Chapter 10 101
- Chapter 10 Other Features 102
- Appendices 103
- MIDI Implementation Chart 105
- Specifications 106
- ■ Mac OS 108
- ■ Windows 108
- ■ What is USB Driver? 109
- About the Driver Modes 110
- Installing the Special Driver 111
- System icon may be displayed 113
- Windows 2000 users 114
- Windows Me/98 users 117
- Windows XP/2000 users 118
- Windows Me users 119
- Windows 98 users 120
- Driver settings 123
- Input/output device settings 124
- Software settings 125
- Mac OS 9 users 129
- OMS settings 130
- FreeMIDI settings 133
- Installing the ASIO driver 135
- Mac OS X users 136
- Adjusting the audio latency 141
- Using ASIO Direct Monitor 141
- If using Windows: 142
- If using Macintosh: 142
- Troubleshooting 143
- Other Problems 144
- Problems when using the 147
- USB Driver 147
- Deleting the Special Driver 151
- Patch List 152
- ■ Preset Patch 156
- IMPORTANT SAFETY INSTRUCTIONS 163
- SAVE THESE INSTRUCTIONS 163
Related products and manuals for Supplementary music equipment Roland GT-PRO
(184 pages)© 2020, manymanuals.com. All rights reserved. | 2.038 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals