Roland GT-PRO Owner's Manual Page 62
- Page / 164
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
62
Chapter 6 Using Pedals to Control the Effects
Setting the Operation of the External
Foot Switch (CTL 1, 2, 3, 4 Function)
This applies the settings determining the function of the foot
switches connected to the CTL 1/2 and CTL 3/4 jacks as
global settings for the entire GT-PRO.
* The correspondence between the pedal switch (A/B) and CTL
function when an FS-6 is connected is shown below.
fig.06-0010
* The following shows the correspondence between the foot
switch and CTL function when two foot switches are
connected using a special connection cable (Roland PCS-31:
sold separately).
fig.06-0020
* When connecting foot switches individually, the settings for
the CTL Function 1 and CTL Function 2 are enabled.
fig.06-0030
1. Press [SYSTEM].
2. Press PARAMETER [ ] [ ] so that “CTL1 Func,”
“CTL2 Func,” “CTL3 Func,” or “CTL4 Func” is
displayed.
fig.06-0040d
3. Use the PATCH/VALUE dial to select the external foot
switch function.
4. Repeat Steps 2 and 3 as needed.
5. Press [EXIT] to return to the Play screen.
CTL 1CTL 2CTL 3CTL 4
CTL 1CTL 2CTL 3CTL 4
PCS-31PCS-31
Red WhiteRed White
Value Explanation
Assignable
The pedal functions as the type of controller
set with Assign (p. 66) in each individual
patch.
Preamp Ch A/B
Switches between Preamp channel A and B.
Solo On/Off
Switches the Preamp SOLO on and off.
FX-1 On/Off
Switches the FX-1 on and off.
Comp On/Off
Switches the COMP on and off.
Wah On/Off
Switches the WAH on and off.
Loop On/Off
Switches the LOOP 1/2 on and off.
OD/DS On/Off
Switches the OVERDRIVE/DISTORTION
on and off.
Preamp On/Off
Switches the PREAMP/SPEAKER on and
off.
EQ On/Off
Switches the EQ on and off.
FX-2 On/Off
Switches the FX-2 on and off.
Delay On/Off
Switches the DELAY on and off.
Chorus On/Off
Switches the CHORUS on and off.
Reverb On/Off
Switches the REVERB on and off.
Pre Loop On/Off
Switches the PRE LOOP on and off.
Amp Ctl1 On/Off
Switches the AMP CTL 1 on and off.
132
5
- Owner’s Manual 1
- USING THE UNIT SAFELY 3
- IMPORTANT NOTES 5
- Contents 7
- Installing & 9
- Main Features 10
- Front Panel 11
- Rear panel 13
- Signal Flow 14
- Chapter 1 Playing Sounds 15
- Turning on the Power 16
- Adjusting the Input Level 17
- Adjusting the Output Level 17
- Turning Off the Power 18
- What is a Patch? 19
- How to Switch Patches 19
- (Patch Change) 19
- Turning the Effect On and Off 20
- Setting the Effects Simply 21
- (QUICK FX) 21
- Changing the Connection 22
- Naming Patches (Patch Name) 23
- Copying Patches (Patch Copy) 24
- Exchanging Patches 25
- (Patch Exchange) 25
- Initializing Patches 25
- Storing Settings by Effect 26
- (User Quick Settings) 26
- Copying the PREAMP/SPEAKER 27
- Settings to Another Channel 27
- PREAMP/SPEAKER (Preamp/ 28
- Speaker Simulator) 28
- Chapter 4 29
- Type List 30
- OVERDRIVE/DISTORTION 31
- OUTPUT L 32
- OUTPUT R 32
- Using the HOLD (Hold Delay) 34
- COMP (Compressor) 35
- FX-1/FX-2 36
- AW (Auto Wah) 38
- TM (Tone Modify) 38
- GS (Guitar Simulator) 38
- FL (Flanger) 40
- VB (Vibrato) 40
- STR (Sitar Simulator) 42
- FB (Feedbacker) 42
- WSY (Wave Synth) 44
- SEQ (Sub Equalizer) 44
- PS (Pitch Shifter) 46
- 2CE (2 x 2 Chorus) 48
- AR (Auto Riff) 48
- AC (Acoustic Processor) 50
- EQ (Equalizer) 51
- (External Effects Loop) 52
- PRE LOOP 53
- AMP CTL (Amp Control) 1/2 54
- FX CHAIN (Effect Chain) 56
- NAME (Patch Name) 56
- Chapter 5 57
- Customizing the Speakers 58
- Customizing 59
- Overdrive/Distortion 59
- Customizing Pedal Wah 60
- Use-Specific Guide 61
- PCS-31PCS-31 62
- Red WhiteRed White 62
- EXP Pedal (EXP1, 2 Function) 63
- Chapter 6 65
- Quick Settings 66
- Target Range 68
- Internal Pedal System 70
- Chapter 7 72
- Transmitting and Receiving 75
- MIDI Data 75
- MIDI Device (Bulk Load) 76
- Changing Patch Numbers on an 78
- About MIDI 79
- About the MIDI implementation 80
- Chapter 8 81
- GT-PRO to the FC-200 82
- Controlling the GT-PRO with 83
- EXP Pedal CC#7 CC#7 Function 84
- Pedal Connected to the 84
- FOOT SW/EXP 1 Jack 84
- CC#1 CC#1 Function 84
- Advanced Settings 86
- Before Connecting with USB 88
- Setting USB-Related Functions 89
- Recording the GT-PRO’s 90
- Output with a Computer 90
- Running the GT-PRO from a 91
- Computer 91
- Adjusting the overall sound 94
- Adjusting the Display 96
- Contrast (LCD Contrast) 96
- Switching the Sounds Input 96
- Switched (Patch Extent) 98
- Setting the Knob Functions 99
- (Knob Mode) 99
- Checking the Effect Level 100
- Chapter 10 101
- Chapter 10 Other Features 102
- Appendices 103
- MIDI Implementation Chart 105
- Specifications 106
- ■ Mac OS 108
- ■ Windows 108
- ■ What is USB Driver? 109
- About the Driver Modes 110
- Installing the Special Driver 111
- System icon may be displayed 113
- Windows 2000 users 114
- Windows Me/98 users 117
- Windows XP/2000 users 118
- Windows Me users 119
- Windows 98 users 120
- Driver settings 123
- Input/output device settings 124
- Software settings 125
- Mac OS 9 users 129
- OMS settings 130
- FreeMIDI settings 133
- Installing the ASIO driver 135
- Mac OS X users 136
- Adjusting the audio latency 141
- Using ASIO Direct Monitor 141
- If using Windows: 142
- If using Macintosh: 142
- Troubleshooting 143
- Other Problems 144
- Problems when using the 147
- USB Driver 147
- Deleting the Special Driver 151
- Patch List 152
- ■ Preset Patch 156
- IMPORTANT SAFETY INSTRUCTIONS 163
- SAVE THESE INSTRUCTIONS 163
Related products and manuals for Supplementary music equipment Roland GT-PRO
(184 pages)© 2020, manymanuals.com. All rights reserved. | 1.642 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals