Roland GT-PRO Owner's Manual download pdf (Page 64)

Chapter 6 Using Pedals to Control the Effects

Setting the Operation for an External MIDI

Device (CC#7, CC#80, CC#1 Function)

These settings are applied to the entire GT-PRO, controlling

the GT-PRO by means of Control Change messages from an

FC-200 or other external MIDI device connected to the GT-

PRO via MIDI.

The following describes the settings for Control Change No.

7 (CC#7), No. 80 (CC#80), and No. 1 (CC#1).

fig.06-0070

1. Press [SYSTEM].

2. Press PARAMETER [ ] [ ] so that “CC#7 Func,”

“CC#80 Func,” or “CC#1 Func” is displayed.

fig.06-0080d

3. Use the PATCH/VALUE dial to set how the Control

Change messages are used.

4. Repeat Steps 2 and 3 as needed.

5. Press [EXIT] to return to the Play screen.

CC#7

If operating the expression pedal or FC-200 EXP pedal

with the EXP1 function, EXP2 function, and CC#7

function all set, be sure to have different functions

assigned to each pedal.

If the same function is assigned to different pedals,

operation normally functions according to the value of

the last pedal adjusted, but may not work as intended

when Assign Hold (p. 99) is set to “On.”

CC#80

When Using the FC-200

When the FC-200 is set to its default settings, the

correspondence between CC#7, CC#80, and CC#1 and

the FC-200’s controllers is as shown below.

CC#7: EXP pedal

CC#80: CTL pedal

CC#1: External expression pedal connected to the

FOOT SW/EXP 1 jack.

132

Value Explanation

Auto

The pedal normally is used as a “foot vol-

ume” pedal. When Pedal Wah (p. 36) or

Pedal Bend (p. 47) is switched on, the CC#7

then automatically functions as a “pedal

wah” or “pedal bend” pedal.

When Pedal Wah and Pedal Bend are switched off, this automatical-

ly functions as a “foot volume” pedal.

Assignable

The pedal is used as the controller set in As-

sign (p. 66) for each patch.

Foot Volume

The pedal functions as a “foot volume” pedal.

Patch Level

The pedal is used as the patch level controller.

Pedal Wah

The pedal is used as a “pedal wah” pedal

when Pedal Wah is switched on.

Pedal Bend

The pedal is used as a “pedal bend” pedal

when Pedal Bend is switched on.

Value Explanation

Assignable

The pedal functions as the type of controller

set with Assign (p. 66) in each individual

patch.

Preamp Ch A/B

Switches between Preamp channel A and B.

Solo On/Off

Switches the Preamp SOLO on and off.

FX-1 On/Off

Switches the FX-1 on and off.

Comp On/Off

Switches the COMP on and off.

Wah On/Off

Switches the WAH on and off.

Loop On/Off

Switches the LOOP 1/2 on and off.

OD/DS On/Off

Switches the OVERDRIVE/DISTORTION

on and off.

Preamp On/Off

Switches the PREAMP/SPEAKER on and

off.

EQ On/Off

Switches the EQ on and off.

FX-2 On/Off

Switches the FX-2 on and off.

Delay On/Off

Switches the DELAY on and off.

Chorus On/Off

Switches the CHORUS on and off.

Reverb On/Off

Switches the REVERB on and off.

Pre Loop On/Off

Switches the PRE LOOP on and off.

Amp Ctl1 On/Off

Switches the AMP CTL 1 on and off.

Amp Ctl2 On/Off

Switches the AMP CTL 2 on and off.

MANUAL On/Off

Switches the Manual Mode (p. 85) on and

off.

TUNER On/Off

Switches the TUNER/BYPASS on and off.

Master BPM (TAP)

Used for tap input of the Master BPM.

Delay Time (TAP)

Used for tap input of the delay time.

1 2 ... 59 60 61 62 63 64 65 66 67 68 69 ... 163 164

Comments to this Manuals

No comments

Roland GT-PRO Owner's Manual Page 64

Comments to this Manuals

Related products and manuals for Supplementary music equipment Roland GT-PRO